Söker rådgivning om OC och bootproblem

Trädvy Permalänk
Medlem
Plats
Göteborg
Registrerad
Feb 2006

Söker rådgivning om OC och bootproblem

Hej!

Specifikationer:
MB: Gigabyte EP45-DS3
Bios: F8 (Inkluderar uppdateringen "Support DDR2 speed to 1333MHz and beyond by overclocking")
CPU: Intel Core2 Quad Q6600: Revision G0 Stepping B
CPU Kylning: Scythe Ninja 2 CPU Cooler
Minnen: Corsair XMS2 Dominator TwinX DDR2 PC8500/1066MHz CL5 2x1GB (TWIN2X2048-8500C5D)
GFX: ATI Radeon HD4870
PSU: Corsair VX550W PSU

Jag har använt nedanstående inställningar under en längre tid men ständigt haft problem med att datorn rebootar vid post ca hälften av gångerna då jag startar den överklockat, vilket inte har varit ett stort problem eftersom jag sällan har behövt starta om datorn.

Datorn fungerar felfritt väl inne i operativsystemet och även om jag inte stresstestat den maximalt - så har den nästintill aldrig crashat eller rebootat oförklarligt.

Nu kan jag inte längre ha datorn på på nätterna och vill gå till botten med det här och söker eran hjälp! Jag är i övrigt en nybörjare till OC så även tips som inte är direkt kopplade till post-problemet välkomnas (t.ex memory timings, voltinställningar m.m).

Citat:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...................: Auto
CPU Clock Ratio ...........................: 8.0
Fine CPU Clock Ratio.......................: 0
CPU Frequency .............................: 3.20Ghz

Clock Chip Control
Standard Clock Control
CPU Host Clock Control....................: [Enabled]
CPU Host Frequency (Mhz) .................: 400 Mhz
PCI Express Frequency (Mhz) ..............: Auto
C.I.A.2 ..................................:[Disabled] (Standard)

Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800 (Standard)
PCI Express Clock Drive...................: 900 (Standard)
CPU Clock Skew (ps).......................: (Standard)
MCH Clock Skew (ps).......................: (Standard)

DRAM Performance Control
Performance Enhance.......................: [STANDARD]
Extreme Memory Profile (X.M.P.)...........: Disabled
(G)MCH Frequency Latch....................: [Auto]
System Memory Multiplier .................: 2.66D
Memory Frequency (Mhz) ...................: 1066Mhz
DRAM Timing Selectable ...................: [Auto]

Standard Timing Control
CAS Latency Time..........................: 5 (Auto)
tRCD .....................................: 7 (Auto)
tRP'......................................: 7 (Auto)
tRAS......................................: 24 (Auto)

Advanced Timing Control
tRRD......................................: 4 [Auto]
tWTR......................................: 4 [Auto]
tWR.......................................: 8 (Auto)
tRFC......................................: 68 (Auto)
tRTP......................................: 4 [Auto]
Command Rate (CMD) .......................: 0 (Auto)

Channel A
Static tRead Value........................: 6 [Auto]
tRD Phase0 Adjustment....................: 0 [Auto]
tRD Phase1 Adjustment.....................: 0 [Auto]
tRD Phase2 Adjustment ...................: 0 [Auto]
tRD Phase3 Adjustment....................: 0 [Auto]
Trd2rd(Different Rank)....................: 8 [Auto]
Twr2wr(Different Rank)....................: 8 [Auto]
Twr2rd(Different Rank)....................: 7 [Auto]
Trd2wr(Same/Diff Rank)....................: 9 [Auto]
Dimm1 Clock Skew Control..................:Auto ps
Dimm2 Clock Skew Control..................:Auto ps

Channel B
Static tRead Value........................: 7 [Auto]
tRD Phase0 Adjustment....................: 0 [Auto] <<< Leave for all below as well
tRD Phase1 Adjustment.....................: 0 [Auto]
tRD Phase2 Adjustment ...................: 0 [Auto]
tRD Phase3 Adjustment....................: 0 [Auto]
Trd2rd(Different Rank)....................: 8 [Auto]
Twr2wr(Different Rank)....................: 8 [Auto]
Twr2rd(Different Rank)....................: 7 [Auto]
Trd2wr(Same/Diff Rank)....................: 9 [Auto]
Dimm1 Clock Skew Control..................:Auto ps
Dimm2 Clock Skew Control..................:Auto ps

Motherboard Voltage Control

CPU
CPU Vcore….………............................: 1.33125 (Auto dvs standardinställing ger 1.204-1.220V i Bios)
CPU Termination…..........................: 1.2 [Auto]
CPU PLL…………………............................: 1.5 [Auto]
CPU Referene…………..........................: 0.76 [Auto]

MCH/ICH
MCH Core…………….............................: 1.20V (1.1 standard)
MCH Reference….…….0.760V..................: Standard
MCH/DRAM Ref.…......0.900V................: Standard
ICH I/O……………….....1.500V..................: Standard
ICH Core…………...……1.100V...................: Standard

DRAM
DRAM Voltage ……....1.800V.................: 2.1
DRAM Termination .…0.900V.................: Standard
Channel A Reference 0.900V................: Standard
Channel B Reference 0.900V................: Standard

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect.................: [Enabled]
CPU Enhanced Halt (C1E)...................: [Disabled]
C2/C2E State Support......................: [Disabled]
x C4/C4E State Support....................: [Disabled]
CPU Thermal Monitor 2(TM2) ...............: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology.................: [Enabled]

Integrated Peripherals
Legacy USB Storage Detect ................: [Disabled]

Trädvy Permalänk
Medlem
Plats
Göteborg
Registrerad
Feb 2006

Bump