Problem vid installation av os på sprillans SSD

Trädvy Permalänk
Medlem
Plats
Västerås
Registrerad
Maj 2010

Problem vid installation av os på sprillans SSD

Morsning! Har köpt en SSD som ska ersätta min mekaniska disk som systemdisk. Jag har kopplat ifrån den gamla disken och satt i enbart SSD i en SATA 6GB/S port.
Jag startar windows 8 installationsprogrammet från en USB sticka, och när jag kommer till momentet där man väljer en disk så syns min SSD där och går att formatera.

Kruxet är att när jag ska påbörja själva installationen så säger den att det följande "Windows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure the disk's controller is enabled in the computer's BIOS menu"

Jag har AHCI på och provat installera i IDE.

Specs:
Sabretooth 990FX
amd phenom II x4 965

SSD disken är en Kingston SSD v300 120GB

Trädvy Permalänk
Medlem
Registrerad
Apr 2002
Skrivet av nnahnneh:

Morsning! Har köpt en SSD som ska ersätta min mekaniska disk som systemdisk. Jag har kopplat ifrån den gamla disken och satt i enbart SSD i en SATA 6GB/S port.
Jag startar windows 8 installationsprogrammet från en USB sticka, och när jag kommer till momentet där man väljer en disk så syns min SSD där och går att formatera.

Kruxet är att när jag ska påbörja själva installationen så säger den att det följande "Windows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure the disk's controller is enabled in the computer's BIOS menu"

Jag har AHCI på och provat installera i IDE.

Specs:
Sabretooth 990FX
amd phenom II x4 965

SSD disken är en Kingston SSD v300 120GB

Okej... Är du helt säker på att du valt AHCI (för rätt kontroller) samt anslutit SSDn till denna kontroller?

Intel i7 6850k || Asus X99-A II || Evga GTX 980Ti || Kingston HyperX Fury 2666 64GB || Samsung 950 Pro 512GB || XB270HU 1440p IPS G-Sync

Trädvy Permalänk
Medlem
Plats
SweClockers forum
Registrerad
Aug 2012

Är disken MBR eller GPT?
Kör du UEFI eller Legacy?

Guide: Roota din HTC - BB-Kod-knappar på Prisjakt

              Min burk - Kvävekyld till 80%
Phenom II X4 965@3900MHz (Sommarklock)
GTX 760@1111MHz

Ibland har jag fel, men då är det någon annans fel.

Trädvy Permalänk
Medlem
Plats
Västerås
Registrerad
Maj 2010
Skrivet av evil penguin:

Okej... Är du helt säker på att du valt AHCI (för rätt kontroller) samt anslutit SSDn till denna kontroller?

Aa AHCI är enabled sata port 1-6 som är grundkontrollern controllern. (har provat både port 1 och 3

Skrivet av LemonIllusion:

Är disken MBR eller GPT?
Kör du UEFI eller Legacy?

Hur tar jag reda på det och vad innebär dom olika förkorttningarna?

Trädvy Permalänk
Medlem
Plats
SweClockers forum
Registrerad
Aug 2012
Skrivet av nnahnneh:

Hur tar jag reda på det och vad innebär dom olika förkorttningarna?

GPT och MBR är två olika sorters "format" på en hårddisk. Det ligger på en nivå under partitionerna.
I windows 7 kan du se vilket du har på detta sätt.

Dold text

Legacy BIOS och UEFI behöver jag nog inte gå in i detalj på men man måste iaf köra UEFI för att kunna boota från GPT. Det kan även vara så att du inte kan boota från MBR med UEFI men är inte det minsta säker på detta.
Du väljer vilket av dessa du vill bruka i inställningarna i BIOS.

Guide: Roota din HTC - BB-Kod-knappar på Prisjakt

              Min burk - Kvävekyld till 80%
Phenom II X4 965@3900MHz (Sommarklock)
GTX 760@1111MHz

Ibland har jag fel, men då är det någon annans fel.

Trädvy Permalänk
Medlem
Plats
Västerås
Registrerad
Maj 2010
Skrivet av LemonIllusion:

GPT och MBR är två olika sorters "format" på en hårddisk. Det ligger på en nivå under partitionerna.
I windows 7 kan du se vilket du har på detta sätt.

Legacy BIOS och UEFI behöver jag nog inte gå in i detalj på men man måste iaf köra UEFI för att kunna boota från GPT. Det kan även vara så att du inte kan boota från MBR med UEFI men är inte det minsta säker på detta.
Du väljer vilket av dessa du vill bruka i inställningarna i BIOS.

Nu har jag kopplat in den gamla disken och kör båda samtidigt och nu visas SSD'n som "Lagringsutrymme"

Jag får ingen information om hårddisken utan allt är bara streckat
Disk -
Typ -
Status -
Och så vidare..

SMART READ DATA

SMART READ DATA Revision: 10 Attributes List 1: (SSD Raw Read Error Rate) Normalized Rate: 120 Sectors Read: 0 Read Errors: 11 5: (SSD Retired Block Count) Spare blocks remaining 100% Retired Block 0 9: (SSD Power-On Hours) Value 100 Total 17 hrs 25 mins 12: (SSD Power Cycle Count) Power Cycle Life Remaining 100% Number of power cycles 7 171: (SSD Program Fail Count) Program Error Count 0 172: (SSD Erase Fail Count) Erase Error Count 0 174: (SSD Unexpected power loss count) Unexpected power loss Count 6 177: (Wear Range Delta) Wear Range Delta 0% 181: (Program Fail Count) Program Error Count 0 182: (Erase Fail Count) Erase Error Count 0 187: (SSD Reported Uncorrectable Errors) Normalized Value 100 lifetime URAISE Errors 0 189: (Unrecognized Attribute) Value: 25 Raw Data: 19 00 42 00 17 00 00 194: (SSD Temperature Monitoring) Normalized temp 25 Current 25 High 66 Low 23 195: (SSD ECC On-the-fly Count) Normalized Value 100 Sectors Read 0 UECC Count 11 196: (SSD Reallocation Event Count) Normalized Value 100 Reallocation Event Count 0 201: (SSD Uncorrectable Soft Read Error Rate)Normalized Value 100 Sectors Read 0 Uncorrectable Soft Error Count 11 204: (SSD Soft ECC Correction Rate (RAISE) Normalized Value 100 Sectors Read 0 Soft ECC Correction Count 11 230: (SSD Life Curve Status) Normalized Value 100 231: (SSD Life Left) Life Remaining 100% 233: (SSD Internal Reserved) 1 234: (SSD Internal Reserved) 1 241: (SSD Lifetime writes from host) lifetime writes 1 242: (SSD Lifetime reads from host) lifetime reads 0

Dold text

Identify data

Citat:

[CODE] Drive Name = [\\.\PHYSICALDRIVE1]
Display Name = [Drive1]
Drive Number = [1]
Model Number = [KINGSTON SV300S37A120G]
WorldwideName = [00-26-b7 23402ecef]
Capacity = [120GB]
Serial Number = [50026B723402ECEF]
Fw Revision = [506ABBF0]
Config ID = [27096]
Customer ID = []
OEM ID = [Š]
Drive Size = [120034123776] (111 GB)
Raw Capacity (# of sectors) = [268435456]

Citat:
Citat:

<IDENTIFY DEVICE DATA>
Note: All references are to ACS-2 Specification
Legend: F/V/X - Fixed/variable/undefined Content
(O)/(M) - Mandatory/optional requirement

Word 00: (M) 0c5ah General configuration
F 0b 15 0 = ATA device
X 0001100b 14:8 Retired
F 01b 7:6 Obsolete
X 011b 5:3 Retired
V 0b 2 Response incomplete
X 1b 1 Retired
0b 0 Reserved

Word 01: 3fffh Obsolete

Word 02: (O) c837h Specific configuration

Word 03: (X) 0010h Obsolete

Word 04: (X) 0000h 0000h Retired

Word 06: (X) 003fh Obsolete

Word 07: 0000h 0000h Reserved for assignment by the CompactFlashTM Association

Word 09: (X) 0000h Retired

Word 10: (M) Serial number (20 ASCII characters)
F 3530h 3032h 3642h 3732h 3334h 3032h 4543h 4546h 2020h 2020h
50026B723402ECEF
Word 20: X 0000h 0000h Retired

Word 22: X 0004h Obsolete

Word 23: (M) Firmware revision (8 ASCII characters)
F 3530h 3641h 4242h 4630h
506ABBF0
Word 27: (M) Model number (40 ASCII characters)
F 4b49h 4e47h 5354h 4f4eh 2053h 5633h 3030h 5333h 3741h 3132h
3047h 2020h 2020h 2020h 2020h 2020h 2020h 2020h 2020h 2020h
KINGSTON SV300S37A120G
Word 47: (M) 8010h
F 15:8 80h
F 7:0 00h = Reserved
01h-FFh = Maximum number of logical sectors that shall be transferred per DRQ data block on READ/WRITE MULTIPLE commands

Word 48: (0) 4000h Trusted Computing feature set options
F 15 Shall be cleared to zero
F 14 Shall be set to zero
13:1 Reserved for the Trusted Computing Group
F 0 1=Trusted Computing feature set is supported

Word 49: (M) 2f00h Capabilities
F 15:14 Reserved for the IDENTIFY PACKET DEVICE command.
F 1b 13 1 = Standby timer values as specified in this standard are supported
0 = Standby timer values shall be managed by the device
F 0b 12 Reserved for the IDENTIFY PACKET DEVICE command.
F 1b 11 1 = IORDY supported
0 = IORDY may be supported
F 1b 10 1 = IORDY may be disabled
F 1b 9 1 = LBA supported
F 1b 8 1 = DMA supported
X 00000000b 7:0 Retired

Word 50: (M) 4000 Capabilities
F 0b 15 Shall be cleared to zero.
F 1b 14 Shall be set to one.
F 000000000000b 13:2 Reserved.
X 0b 1 Obsolete
F 0b 0 Shall be set to one to indicate a device specific Standby timer value

Word 51: X 0200h 0200h Obsolete

Word 53: (M) 0007h
F 0000000000000b 15:3 Reserved
F 1b 2 1 = the fields reported in word 88 are valid
0 = the fields reported in word 88 are not valid
F 1b 1 1 = the fields reported in words (70:64) are valid
0 = the fields reported in words (70:64) are not valid
X 1b 0 Obsolete

Word 54: Obsolete
X 3fffh 0010h 003fh fc10h

Word 59: (M) 0110h
F 0000000b 15:9 Reserved
V 1b 8 1 = Multiple sector setting is valid
V 10h 7:0 xxh = Current setting for number of logical sectors that shall be transferred per DRQ data block on READ/WRITE Multiple commands

Word 60: (M) 4bb0h 0df9h Total number of user addressable logical sectors (DWord)

Word 62: X 0000h Obsolete

Word 63: (M) 0007h
F 00000b 15-11 Reserved
V 0b 10 1 = Multiword DMA mode 2 is selected
0 = Multiword DMA mode 2 is not selected
V 0b 9 1 = Multiword DMA mode 1 is selected
0 = Multiword DMA mode 1 is not selected
V 0b 8 1 = Multiword DMA mode 0 is selected
0 = Multiword DMA mode 0 is not selected
F 00000b 7:3 Reserved
F 1b 2 1 = Multiword DMA mode 2 and below are supported
F 1b 1 1 = Multiword DMA mode 1 and below are supported
F 1b 0 1 = Multiword DMA mode 0 is supported

Word 64: (M) 0003h
F 15:8 Reserved
F 7:0 PIO modes supported

Word 65: (M) 0078h Minimum Multiword DMA transfer cycle time per word
F 15:0 Cycle time in nanoseconds

Word 66: (M) 0078h Manufacturer's recommended Multiword DMA cycle time
F 15:0 Cycle time in nanoseconds

Word 67: (M) 0078h Minimum PIO transfer cycle time without flow control
F 15:0 Cycle time in nanoseconds

Word 68: (M) 0078h Minimum PIO transfer cycle time with IORDY flow control
F 15:0 Cycle time in nanoseconds

Word 69: (O) 4200h Additional Supported
F 0b 15 1 = CFast Specification Support
F 1b 14 1 = Deterministic read after TRIM is supported
F 0b 13 1 = Long Physical Sector Alignment Error Reporting Control is supported
F 0b 12 1 = DEVICE CONFIGURATION IDENTIFY DMA and
DEVICE CONFIGURATION SET DMA are supported
F 0b 11 1 = READ BUFFER DMA is supported
F 0b 10 1 = WRITE BUFFER DMA is supported
F 1b 9 1 = SET MAX SET PASSWORD DMA and
SET MAX UNLOCK DMA are supported
F 0b 8 1 = DOWNLOAD MICROCODE DMA is supported
F 00000000b 7:0 Reserved

Word 70: X 0000h Reserved

Word 71: Reserved for IDENTIFY PACKET DEVICE command.
0000h 0000h 0000h 0000h

Word 75: (O) 001fh Queue depth
00000000000b 15:5 Reserved
F 11111b 4:0 Maximum queue depth - 1

Word 76: (O) c70eh Serial ATA capabilities
110b 15:13 Reserved
F 0b 12 Supports Native Command Queuing priority information
F 0b 11 Supports Unload while NCQ commands outstanding
F 1b 10 Supports Phy event counters
F 1b 9 Supports receipt of host initiated power management requests
F 1b 8 Supports native command queuing
00001b 7:3 Reserved for Serial ATA
F 1b 2 1 = Supports Serial ATA Gen-2 speed (3.0Gbps)
F 1b 1 1 = Supports Serial ATA Gen-1 speed (1.5Gbps)
F 0b 0 Shall be cleared to zero

Word 77: 0006h Reserved for Serial ATA future definition

Word 78: (O) 004ch Serial ATA features supported
000000000b 15:7 Reserved
F 1b 6 1 = supports software settings preservation
F 0b 5 1 = supports Asynchronous notification
F 0b 4 1 = supports in-order data delivery
F 1b 3 1 = supports dev initiate interface power management
F 1b 2 1 = supports DMA Setup Auto-Activate optimization
F 0b 1 1 = supports non-zero buffer offsets in DMA Setup FIS
F 0b 0 Reserved (set to 0)

Word 79: (0) 0040h Serial ATA features enabled
000000000b 15:7 Reserved
V 1b 6 1 = software settings preservation enabled
V 0b 5 1 = Asynchronous notification enabled
V 0b 4 1 = in-order data delivery enabled
V 0b 3 1 = device initiating interface power management enabled
V 0b 2 1 = DMA Setup Auto-Activate optimization enabled
V 0b 1 1 = non-zero buffer offsets in DMA Setup FIS enabled
F 0b 0 Reserved (set to 0)

Word 80: (M) 01fch Major version number
0000h or FFFFh = device does not report version
0000000b 15:9 Reserved
F 1b 8 1 = supports ATA8-ACS
F 1b 7 1 = supports ATA/ATAPI-7
F 1b 6 1 = supports ATA/ATAPI-6
F 1b 5 1 = supports ATA/ATAPI-5
F 1b 4 1 = supports ATA/ATAPI-4
X 1b 3 Obsolete
X 1b 2 Obsolete
X 0b 1 Obsolete
0b 0 Reserved

Word 81: (M) 0110h Minor revision number
F 0000h or FFFFh = device does not report version
F 0001h-000Ch = Obsolete
F 000Dh = ATA/ATAPI-4 X3T13 1153D revision 6
F 000Eh = ATA/ATAPI-4 T13 1153D revision 13
F 000Fh = ATA/ATAPI-4 X3T13 1153D revision 7
F 0010h = ATA/ATAPI-4 T13 1153D revision 18
F 0011h = ATA/ATAPI-4 T13 1153D revision 15
F 0012h = ATA/ATAPI-4 published ANSI NCITS 317-1998
F 0013h = ATA/ATAPI-5 T13 1321D revision 3
F 0014h = ATA/ATAPI-4 T13 1153D revision 14
F 0015h = ATA/ATAPI-5 T13 1321D revision 1
F 0016h = ATA/ATAPI-5 published ANSI NCITS 340-2000
F 0017h = ATA/ATAPI-4 T13 1153D revision 17
F 0018h = ATA/ATAPI-6 T13 1410D revision 0
F 0019h = ATA/ATAPI-6 T13 1410D revision 3a
F 001Ah = ATA/ATAPI-7 T13 1532D revision 1
F 001Bh = ATA/ATAPI-6 T13 1410D revision 2
F 001Ch = ATA/ATAPI-6 T13 1410D revision 1
001Dh Reserved
F 001Eh = ATA/ATAPI-7 T13 1532D revision 0
F 001Fh-0020h = Reserved
F 0021h = ATA/ATAPI-7 T13 1532D revision 4a
F 0022h = ATA/ATAPI-6 published, ANSI INCITS 361-2002
F 0023h-FFFFh Reserved

Word 82: (M) 746bh Commands and feature sets supported
X 0b 15 Obsolete
F 1b 14 1 = NOP command supported
F 1b 13 1 = READ BUFFER command supported
F 1b 12 1 = WRITE BUFFER command supported
X 0b 11 Obsolete
F 1b 10 1 = Host Protected Area feature set supported
F 0b 9 1 = DEVICE RESET command supported
F 0b 8 1 = SERVICE interrupt supported
F 0b 7 1 = release interrupt supported
F 1b 6 1 = look-ahead supported
F 1b 5 1 = write cache supported
F 0b 4 Shall be cleared to zero to indicate that the PACKET feature set is not
supported
F 1b 3 1 = mandatory Power Management feature set supported
F 0b 2 Obsolete
F 1b 1 1 = Security Mode feature set supported
F 1b 0 1 = SMART feature set supported

Word 83: (M) 7469h Commands and feature sets supported
F 0b 15 Shall be cleared to zero
F 1b 14 Shall be set to one
F 1b 13 1 = FLUSH CACHE EXT command supported
F 1b 12 1 = mandatory FLUSH CACHE command supported
F 0b 11 1 = Device Configuration Overlay feature set supported
F 1b 10 1 = 48-bit Address feature set supported
F 0b 9 1 = Automatic Acoustic Management feature set supported
F 0b 8 1 = SET MAX security extension supported
F 0b 7 See Address Offset Reserved Area Boot NCITS TR27:2001
F 1b 6 1 = SET FEATURES subcommand required to spin-up after power-up
F 1b 5 1 = Power-Up In Standby features set supported
X 0b 4 Obsolete
F 1b 3 1 = Advanced Power Management feature set supported
F 0b 2 1 = CFA feature set supported
F 0b 1 1 = READ/WRITE DMA QUEUED supported
F 1b 0 1 = DOWNLOAD MICROCODE command supported

Word 84: (M) 6163h Commands and feature sets supported
F 0b 15 Shall be cleared to zero
F 1b 14 Shall be set to one
F 1b 13 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
F 0b 12 Reserved for technical report INCITS TR-37-2004 (TLC)
F 0b 11 Reserved for technical report INCITS TR-37-2004 (TLC)
X 00b 10:9 1 = Obsolete
F 1b 8 1 = 64-bit Word wide name supported
F 0b 7 1 = WRITE DMA QUEUEDFUA EXT command supported
F 1b 6 1 = WRITE DMA FUA EXT and WRITE MULTI FUA EXT commands supported
F 1b 5 1 = General Purpose Logging feature set supported
F 0b 4 1 = Streaming feature set supported
F 0b 3 1 = Media Card Pass Through Command feature set supported
F 0b 2 1 = Media serial number supported
F 1b 1 1 = SMART self-test supported
F 1b 0 1 = SMART error logging supported

Word 85: (M) 7429h Commands and feature sets supported or enabled
X 0b 15 Obsolete
F 1b 14 1 = NOP command supported
F 1b 13 1 = READ BUFFER command supported
F 1b 12 1 = WRITE BUFFER command supported
X 0b 11 Obsolete
V 1b 10 1 = Host Protected Area feature set enabled
F 0b 9 1 = DEVICE RESET command supported
V 0b 8 1 = SERVICE interrupt enabled
V 0b 7 1 = release interrupt enabled
V 0b 6 1 = look-ahead enabled
V 1b 5 1 = write cache enabled
F 0b 4 Shall be cleared to zero to indicate that the PACKET feature set is not supported.
F 1b 3 1 = Power Management feature set enabled
X 0b 2 Obsolete
V 0b 1 1 = Security Mode feature set enabled
V 1b 0 1 = SMART feature set enabled

Word 86: (M) b449h Commands and feature sets supported or enabled
F 1b 15 1 = Words 120-119 are valid
0b 14 1 = Reserved
F 1b 13 1 = FLUSH CACHE EXT command supported
F 1b 12 1 = FLUSH CACHE command supported
F 0b 11 1 = DCO feature set is supported
F 1b 10 1 = 48-bit Address features set supported
V 0b 9 1 = Automatic Acoustic Management feature set enabled
V 0b 8 1 = SET MAX security enabled by SET MAX SET PASSWORD
0b 7 Reserved for address Offset Reserved Area Boot,INCITS TR27:2001
F 1b 6 1 = SET FEATURES subcommand required to spin-up after power-up
V 0b 5 1 = Power-Up In Standby features set enabled
X 0b 4 Obsolete
V 1b 3 1 = Advanced Power Management feature set enabled
F 0b 2 1 = CFA feature set supported
F 0b 1 1 = READ/WRITE DMA QUEUED command supported
F 1b 0 1 = DOWNLOAD MICROCODE command supported

Word 87: (M) 6163h Commands and feature sets supported or enabled
F 0b 15 Shall be cleared to zero
F 0b 14 Shall be set to one
F 0b 13 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
0b 12 Reserved for technical report- INCITS tr-37-2004 (TLC)
0b 11 Reserved for technical report- INCITS TR-37-2004 (TLC)
X 00b 10:9 Obsolete
F 1b 8 1 = 64 bit Word wide name supported
F 0b 7 1 = WRITE DMA QUEUED FUA EXT command supported
F 1b 6 1 = WRITE DMA FUA EXT and WRITE MULTI FUA EXT commands
supported
F 1b 5 1 = General Purpose Logging feature set supported
X 0b 4 Obsolete
V 0b 3 1 = Media Card Pass Through Command feature set supported
V 0b 2 1 = Media serial number is valid
F 1b 1 1 = SMART self-test supported
F 1b 0 1 = SMART error logging supported

Word 88: (O) 407fh Ultra DMA modes
0b 15 Reserved
V 1b 14 1 = Ultra DMA mode 6 is selected
0 = Ultra DMA mode 6 is not selected
V 0b 13 1 = Ultra DMA mode 5 is selected
0 = Ultra DMA mode 5 is not selected
V 0b 12 1 = Ultra DMA mode 4 is selected
0 = Ultra DMA mode 4 is not selected
V 0b 11 1 = Ultra DMA mode 3 is selected
0 = Ultra DMA mode 3 is not selected
V 0b 10 1 = Ultra DMA mode 2 is selected
0 = Ultra DMA mode 2 is not selected
V 0b 9 1 = Ultra DMA mode 1 is selected
0 = Ultra DMA mode 1 is not selected
V 0b 8 1 = Ultra DMA mode 0 is selected
0 = Ultra DMA mode 0 is not selected
0b 7 Reserved
F 1b 6 1 = Ultra DMA mode 6 and below are supported
F 1b 5 1 = Ultra DMA mode 5 and below are supported
F 1b 4 1 = Ultra DMA mode 4 and below are supported
F 1b 3 1 = Ultra DMA mode 3 and below are supported
F 1b 2 1 = Ultra DMA mode 2 and below are supported
F 1b 1 1 = Ultra DMA mode 1 and below are supported
F 1b 0 1 = Ultra DMA mode 0 is supported

Word 89: (O) 0001h Time required for security erase unit completion
00h 15:8 Reserved
F 01h 7:0 Time required for Normal Erase mode SECUIRYT ERASE UNIT command

Word 90: (O) 0000h Time required for Enhanced security erase completion
00h 15:8 Reserved
F 00h 7:0 Time required for Enhanced Erase mode SECUIRYT ERASE UNIT command

Word 91: (O) 00feh Current APM level value (Advanced Power Management)

Word 92: (O) fffeh Master Password Identifier

Word 93: (M) 0000h Hardware reset result. The contents of bits (12-0) of this world shall change only during the execution of a hardware reset (7.18.7.47)
F 0b 15 Shall be cleared to zero.
F 0b 14 Shall be set to one.
V 0b 13 1 = dev detected CBLID- above ViHB
0 = dev detected CBLID- below ViL
V 00000b 12:8 Device 1 HW reset result. Device 0 shall clear these bits to 0.
Device 1 shall set these bits as follows:
12 Reserved.
11 0 = Device 1 did not assert PDIAG-.
1 = Device 1 asserted PDIAG-.
V 00b 10:9 These bits indicate how Dev 1 determined device number:
00 = Reserved.
01 = a jumper was used.
10 = the CSEL signal was used.
11 = some other method was used or the method is unknown
0b 8 Shall be set to one.
7:0 Device 0 hardware reset result. Device 1 shall clear these bits to 0.
Device 0 shall set these bits as follows:
0b 7 Reserved.
F 0b 6 0 = Device 0 not respond when Device 1 is selected.
1 = Device 0 responds when Device 1 is selected.
V 0b 5 0 = Device 0 did not detect assertion of DASP-.
1 = Device 0 detected assertion of DASP-.
V 0b 4 0 = Device 0 did not detect assertion of PDIAG-.
1 = Device 0 detected assertion of PDIAG-.
V 0b 3 0 = Device 0 failed diagnostics.
1 = Device 0 passed diagnostics.
V 00b 2:1 These bits indicate how Device 0 determined device number:
00 = Reserved.
01 = a jumper was used.
10 = the CSEL signal was used.
11 = some other method was used or the method unknown.
F 0b 0 Shall be set to one.

Word 94: (O) 0000h Current AAM value (see 7.18.7.48)
F 00h 15:8 Vendor's recommended acoustic management value.
V 00h 7:0 Current automatic acoustic management value.

Word 95: (O) 0000h Stream Minimum Request Size

Word 96: (O) 0000h Streaming Transfer Time - DMA

Word 97: (O) 0000h Streaming Access Latency - DMA and PIO

Word 98: (O) 0000h 0000h Streaming Performance Granularity (DWord)

Word 100: (O) Total Number of User Addressable Logical Sectors for 48-bit commands (QWord)
V 2ae5a26bh 0111h 18fc2ch 18f4a0h

Word 104: (O) 0000h Streaming Transfer Time - PIO (see 7.18.7.54)

Word 105: 0001h Reserved

Word 106: (O) 4000h Physical sector size / Logical Sector Size
F 0b 15 Shall be cleared to zero
F 1b 14 Shall be set to one
F 0b 13 1 = Device has multiple logical sectors per physical sector.
F 0b 12 1 = Device Logical Sector Longer than 256 Words
00000000b 11:4 Reserved
F 0000b 3:0 2^x logical sectors per physical sector

Word 107: (O) 0000h Inter-seek delay for ISO-7779 standard acoustic testing in microseconds

Word 108: (M) World wide name
F 00-26-b7 23402ecef IeeeOUI-UniqueID
Word 112: (O) Reserved for 128 bit world wide name extension to 128 bits
0000h 0000h 0000h 0000h

Word 116: (O) 0000h Reserved for INCITS TR-37-2004

Word 117: (O) 0000h 0000h Logical sector size (DWord) (see 7.18.7.61)

Word 119: (M) 401ah Commands and feature sets supported (Continued from words 82..84)
F 0b 15 Shall be cleared to zero
F 1b 14 Shall be set to one
00000000b 13:6 Reserved
F 0b 5 1 = The Free-fall Control feature set is supported
F 1b 4 1 = The DOWNLOAD MICROCODE command with mode 3 is supported
F 1b 3 1 = The READ LOG DMA EXT and WRITE LOG DMA EXT commands are supported
F 0b 2 1 = The WRITE UNCORRECTABLE EXT command is supported
F 1b 1 1 = The Write-Read-Verify feature set is supported
0b 0 Reserved for DDT

Word 120: (M) 4018h Commands and feature sets supported or enabled (Continued from words 85..87)
F 0b 15 Shall be cleared to zero
F 1b 14 Shall be set to one
00000000b 13:7 Reserved
V 0b 6 1 = Extended Status Reporting feature set is supported
V 0b 5 1 = The Free-fall Control feature set is enabled
F 1b 4 1 = The DOWNLOAD MICROCODE command with mode 3 is supported
F 1b 3 1 = The READ LOG DMA EXT and WRITE LOG DMA EXT commands are supported
F 0b 2 1 = The WRITE UNCORRECTABLE EXT command is supported
V 0b 1 1 = The Write-Read-Verify feature set is enabled
0b 0 Reserved for DDT

Word 121: Reserved for expanded supported and enable settings
0000h 0000h 0000h 0000h 0000h 0000h

Word 127: 0000h Obsolete

Word 128: (O) 0009h Security status
0000000b 15:9 Reserved
V 0b 8 Master Password Capability 0 = High, 1 = Maximum
00b 7:6 Reserved
F 0b 5 1 = Enhanced security erase supported
V 0b 4 1 = Security count expired
V 1b 3 1 = Security frozen
V 0b 2 1 = Security locked
V 0b 1 1 = Security enabled
F 1b 0 1 = Security supported

Word 129: Vendor specific
0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h
0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h
0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h
0000h 0000h 0000h 0000h 0000h 0000h 0000h

Word 160: (O) 0000h CFA power mode (see 7.18.7.68)
F 0b 15 Word 160 supported
0b 14 Reserved
F 0b 13 CFA power mode 1 is required for one or more commands
implemented by the device
V 0b 12 CFA power mode 1 disabled
F 000000000000b 11:0 Maximum current in ma

Word 161: Reserved for the CompactFlashTM Association
0000h 0000h 0000h 0000h 0000h 0000h 0000h

Word 168: (O) 0000h See 7.18.7.70
000000000000b 15:4 Reserved
F 0000b 3:0 Device Nomimal Form Factor

Word 169: (O) 0001h DATA SET MANAGEMENT is supported (see 7.18.7.71)
000000000000000b 15:1 Reserved
F 1b 0 1 = th Trim bit in the DATA SET MANAGEMENT is supported

Word 170: (O) Addtional Product Identify (ATA String) (see 7.18.7.72)
0000h 0000h 0000h 0000h

Word 174: 0000h 0000h Reserved

Word 176: (O) Current media serial number (60 ASCII characters)
0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h
0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h
0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h
0000h 0000h 0000h 0000h 0000h 0000h

Word 206: (O) 0021h SCT Command Transport
X 0000b 15:12 Vender Specific
000000b 11:6 Reserved
F 1b 5 SCT Command Transport Data Tables support
F 0b 4 SCT Command Transport Features Control supported
F 0b 3 SCT Command Transport Error Recovery control supported
F 0b 2 SCT Command Transport Write Same supported
F 0b 1 SCT Command Transport Long Sector Access supported
F 1b 0 SCT Command Transport supported

Word 207: 0000h 0000h Reserved for CE-ATA

Word 209: (O) 4000h Alignment of logical blocks within a larger physical block
0b 15 Shall be cleared to zero
1b 14 Shall be set to one
00000000000000b 13:0 Logical sector offset within the first physical sector where the first logical sector is placed

Word 210: (O) 0000h 0000h Write-Read-Verify Sector Count Mode 3 Only (DWord)

Word 212: (O) 0100h 0000h Write-Read-Verify Sector Count Mode 2 Only (DWord)

Word 214: (O) 0000h NV Cache Capabilities
F 0000b 15:12 NV Cache feature set version
F 0000b 11:8 NV Cache Power Mode feature set version
000b 7:5 Reserved
V 0b 4 1 = NV Cache feature set enabled
00b 3:2 Reserved
V 0b 1 1 = NV Cache Power Mode feature set enabled
F 0b 0 1 = NV Cache Power Mode feature set supported

Word 215: (O) 0000h NV Cache Size in Logical Blocks (DWord)

Word 217: (M) 0001h Nominal media rotation rate

Word 218: 0000h Reserved

Word 219: (O) 0000h NV Cache Options
15:8 Reserved
F 00h 7:0 Device Estimated Time to Spin Up in Seconds

Word 220: (O) 0000h See 7.18.7.84
15:8 Reserved
V 00h 7:0 Write-Read-Verify feature set current mode

Word 221: 0000h Reserved

Word 222: (M) 103fh Transport Major revision number. 0000h or FFFFh = device does not report version
F 0001b 15:12 Transport Type - 0 = Parallel, 1 = Serial, 2-Fh = Reserved
00000011b 11:4 Reserved Reserved
F 1b 3 Reserved SATA Rev 2.5
F 1b 2 Reserved SATA II: Extensions
F 1b 1 ATA/ATAPI-7 SATA 1.0a
F 1b 0 ATA8-APT ATA8-AST

Word 223: (M) 0000h Transport Minor revision number

Word 224: Reserved for CE-ATA
0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h
0000h 0000h

Word 234: (O) 0000h Minimum number of 512 byte units per DOWNLOAD MICROCODE command mode 03h

Word 235: (O) 0000h Maximum number of 512 byte units per DOWNLOAD MICROCODE command mode 03h

Word 236: Reserved
0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h
0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h
0000h 0000h 0000h

Word 255: (M) 71a5h Integrity word
71h 15:8 Checksum
a5h 7:0 Signature
[/CODE]

Dold text
Trädvy Permalänk
Medlem
Plats
SweClockers forum
Registrerad
Aug 2012
Skrivet av nnahnneh:

Nu har jag kopplat in den gamla disken och kör båda samtidigt och nu visas SSD'n som "Lagringsutrymme"

Jag får ingen information om hårddisken utan allt är bara streckat
Disk -
Typ -
Status -
Och så vidare..

SMART READ DATA

SMART READ DATA Revision: 10 Attributes List 1: (SSD Raw Read Error Rate) Normalized Rate: 120 Sectors Read: 0 Read Errors: 11 5: (SSD Retired Block Count) Spare blocks remaining 100% Retired Block 0 9: (SSD Power-On Hours) Value 100 Total 17 hrs 25 mins 12: (SSD Power Cycle Count) Power Cycle Life Remaining 100% Number of power cycles 7 171: (SSD Program Fail Count) Program Error Count 0 172: (SSD Erase Fail Count) Erase Error Count 0 174: (SSD Unexpected power loss count) Unexpected power loss Count 6 177: (Wear Range Delta) Wear Range Delta 0% 181: (Program Fail Count) Program Error Count 0 182: (Erase Fail Count) Erase Error Count 0 187: (SSD Reported Uncorrectable Errors) Normalized Value 100 lifetime URAISE Errors 0 189: (Unrecognized Attribute) Value: 25 Raw Data: 19 00 42 00 17 00 00 194: (SSD Temperature Monitoring) Normalized temp 25 Current 25 High 66 Low 23 195: (SSD ECC On-the-fly Count) Normalized Value 100 Sectors Read 0 UECC Count 11 196: (SSD Reallocation Event Count) Normalized Value 100 Reallocation Event Count 0 201: (SSD Uncorrectable Soft Read Error Rate)Normalized Value 100 Sectors Read 0 Uncorrectable Soft Error Count 11 204: (SSD Soft ECC Correction Rate (RAISE) Normalized Value 100 Sectors Read 0 Soft ECC Correction Count 11 230: (SSD Life Curve Status) Normalized Value 100 231: (SSD Life Left) Life Remaining 100% 233: (SSD Internal Reserved) 1 234: (SSD Internal Reserved) 1 241: (SSD Lifetime writes from host) lifetime writes 1 242: (SSD Lifetime reads from host) lifetime reads 0

Identify data

Dold text

SÄTT SPOILER!
Du har nog missat steg sex. Klicka på uppdatera.

Guide: Roota din HTC - BB-Kod-knappar på Prisjakt

              Min burk - Kvävekyld till 80%
Phenom II X4 965@3900MHz (Sommarklock)
GTX 760@1111MHz

Ibland har jag fel, men då är det någon annans fel.