Hjälp med felsökning, Fildelning Ubuntu <--> Win8.1 med Samba

Permalänk
Medlem

Hjälp med felsökning, Fildelning Ubuntu <--> Win8.1 med Samba

Hej!
Jag har problem att få fildelning mellan Ubuntu och win8 att fungera till 100%. Jag googlat mig röd i ögonen och visst finns det trådar med liknande problem men inget jag testat hjälper mig.

Dator HTPC:
Ubuntu 14.04
Trådad anslutning till router

Dator SKYNET:
Win 8.1
Trådad anslutning till router

Från HTPC kan jag se filer jag delat ut från SKYNET. Jag kan browsa dessa mappar och det fungerar bra.

Om jag delar ut en mapp från systemdisken på HTPC med högerklick/delningar på lokalt nätverk/ (bokar i gäst och dela med andra). Då ser jag mappen från SKYNET och kan browsa denna.

Nu till problemet:
1. Om jag delar ut en disk eller mapp som inte ligger på systemdisken på HTPC så ser jag mappen i SKYNET. Men försöker jag gå in i den blir det "ÅTKOMST NEKAD".
2. Om jag startar om HTPC efter att jag delat en disk eller mapp som inte ligger på systemdisken glömmer den bort att jag delat nästa gång jag kommer in i ubuntu.

Ideér?

smb.conf:

# # Sample configuration file for the Samba suite for Debian GNU/Linux. # # # This is the main Samba configuration file. You should read the # smb.conf(5) manual page in order to understand the options listed # here. Samba has a huge number of configurable options most of which # are not shown in this example # # Some options that are often worth tuning have been included as # commented-out examples in this file. # - When such options are commented with ";", the proposed setting # differs from the default Samba behaviour # - When commented with "#", the proposed setting is the default # behaviour of Samba but the option is considered important # enough to be mentioned here # # NOTE: Whenever you modify this file you should run the command # "testparm" to check that you have not made any basic syntactic # errors. #======================= Global Settings ======================= [global] ## Browsing/Identification ### # Change this to the workgroup/NT-domain name your Samba server will part of workgroup = WORKGROUP # server string is the equivalent of the NT Description field server string = %h server (Samba, Ubuntu) # Windows Internet Name Serving Support Section: # WINS Support - Tells the NMBD component of Samba to enable its WINS Server # wins support = no # WINS Server - Tells the NMBD components of Samba to be a WINS Client # Note: Samba can be either a WINS Server, or a WINS Client, but NOT both ; wins server = w.x.y.z # This will prevent nmbd to search for NetBIOS names through DNS. dns proxy = no ; guest account = nobody log file = /var/log/samba-log.%m lock directory = /var/lock/samba share modes = yes #### Networking #### # The specific set of interfaces / networks to bind to # This can be either the interface name or an IP address/netmask; # interface names are normally preferred ; interfaces = lo eth0 # Only bind to the named interfaces and/or networks; you must use the # 'interfaces' option above to use this. # It is recommended that you enable this feature if your Samba machine is # not protected by a firewall or is a firewall itself. However, this # option cannot handle dynamic or non-broadcast interfaces correctly. ; bind interfaces only = true #### Debugging/Accounting #### # This tells Samba to use a separate log file for each machine # that connects log file = /var/log/samba/log.%m # Cap the size of the individual log files (in KiB). max log size = 1000 # If you want Samba to only log through syslog then set the following # parameter to 'yes'. # syslog only = no # We want Samba to log a minimum amount of information to syslog. Everything # should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log # through syslog you should set the following parameter to something higher. syslog = 0 # Do something sensible when Samba crashes: mail the admin a backtrace panic action = /usr/share/samba/panic-action %d ####### Authentication ####### # Server role. Defines in which mode Samba will operate. Possible # values are "standalone server", "member server", "classic primary # domain controller", "classic backup domain controller", "active # directory domain controller". # # Most people will want "standalone sever" or "member server". # Running as "active directory domain controller" will require first # running "samba-tool domain provision" to wipe databases and create a # new domain. server role = standalone server # If you are using encrypted passwords, Samba will need to know what # password database type you are using. passdb backend = tdbsam obey pam restrictions = yes # This boolean parameter controls whether Samba attempts to sync the Unix # password with the SMB password when the encrypted SMB password in the # passdb is changed. unix password sync = yes # For Unix password sync to work on a Debian GNU/Linux system, the following # parameters must be set (thanks to Ian Kahan <<kahan@informatik.tu-muenchen.de> for # sending the correct chat script for the passwd program in Debian Sarge). passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . # This boolean controls whether PAM will be used for password changes # when requested by an SMB client instead of the program listed in # 'passwd program'. The default is 'no'. pam password change = yes # This option controls how unsuccessful authentication attempts are mapped # to anonymous connections map to guest = bad user ########## Domains ########### # # The following settings only takes effect if 'server role = primary # classic domain controller', 'server role = backup domain controller' # or 'domain logons' is set # # It specifies the location of the user's # profile directory from the client point of view) The following # required a [profiles] share to be setup on the samba server (see # below) ; logon path = \\%N\profiles\%U # Another common choice is storing the profile in the user's home directory # (this is Samba's default) # logon path = \\%N\%U\profile # The following setting only takes effect if 'domain logons' is set # It specifies the location of a user's home directory (from the client # point of view) ; logon drive = H: # logon home = \\%N\%U # The following setting only takes effect if 'domain logons' is set # It specifies the script to run during logon. The script must be stored # in the [netlogon] share # NOTE: Must be store in 'DOS' file format convention ; logon script = logon.cmd # This allows Unix users to be created on the domain controller via the SAMR # RPC pipe. The example command creates a user account with a disabled Unix # password; please adapt to your needs ; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u # This allows machine accounts to be created on the domain controller via the # SAMR RPC pipe. # The following assumes a "machines" group exists on the system ; add machine script = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u # This allows Unix groups to be created on the domain controller via the SAMR # RPC pipe. ; add group script = /usr/sbin/addgroup --force-badname %g ############ Misc ############ # Using the following line enables you to customise your configuration # on a per machine basis. The %m gets replaced with the netbios name # of the machine that is connecting ; include = /home/samba/etc/smb.conf.%m # Some defaults for winbind (make sure you're not using the ranges # for something else.) ; idmap uid = 10000-20000 ; idmap gid = 10000-20000 ; template shell = /bin/bash # Setup usershare options to enable non-root users to share folders # with the net usershare command. # Maximum number of usershare. 0 (default) means that usershare is disabled. ; usershare max shares = 100 # Allow users who've been granted usershare privileges to create # public shares, not just authenticated ones usershare allow guests = yes #======================= Share Definitions ======================= # Un-comment the following (and tweak the other settings below to suit) # to enable the default home directory shares. This will share each # user's home directory as \\server\username ;[homes] ; comment = Home Directories ; browseable = no # By default, the home directories are exported read-only. Change the # next parameter to 'no' if you want to be able to write to them. ; read only = yes # File creation mask is set to 0700 for security reasons. If you want to # create files with group=rw permissions, set next parameter to 0775. ; create mask = 0700 # Directory creation mask is set to 0700 for security reasons. If you want to # create dirs. with group=rw permissions, set next parameter to 0775. ; directory mask = 0700 # By default, \\server\username shares can be connected to by anyone # with access to the samba server. # Un-comment the following parameter to make sure that only "username" # can connect to \\server\username # This might need tweaking when using external authentication schemes ; valid users = %S # Un-comment the following and create the netlogon directory for Domain Logons # (you need to configure Samba to act as a domain controller too.) ;[netlogon] ; comment = Network Logon Service ; path = /home/samba/netlogon ; guest ok = yes ; read only = yes # Un-comment the following and create the profiles directory to store # users profiles (see the "logon path" option above) # (you need to configure Samba to act as a domain controller too.) # The path below should be writable by all users so that their # profile directory may be created the first time they log on ;[profiles] ; comment = Users profiles ; path = /home/samba/profiles ; guest ok = no ; browseable = no ; create mask = 0600 ; directory mask = 0700 [printers] comment = All Printers browseable = no path = /var/spool/samba printable = yes guest ok = no read only = yes create mask = 0700 # Windows clients look for this share name as a source of downloadable # printer drivers [print$] comment = Printer Drivers path = /var/lib/samba/printers browseable = yes read only = yes guest ok = no # Uncomment to allow remote administration of Windows print drivers. # You may need to replace 'lpadmin' with the name of the group your # admin users are members of. # Please note that you also need to set appropriate Unix permissions # to the drivers directory for these users to have write rights in it ; write list = root, @lpadmin

Permalänk
Medlem

Jag har inte läst igenom orda grant nu i din samba fil, men jag ser inget om någon utdelning där. Sedan vill jag även tillägga att jag har aldrig fått fildelning att funka från ubuntu till win genom att höger klicka på mappen i ubuntu.

Här är ett gui program som kan hjälpa dig sätta up allt.

sudo apt-get install system-config-samba

sök bara efter samba när det är installerat så ska du hitta den.

Visa signatur

Смерть -это решение всех проблем. Нет человека - нет проблемы
Comp1: Ubuntu 16.04 Comp2: Arch Linux
Comp3: Ubuntu Server 16.04 Comp4: Centos 6.5
Comp5: Linux mint 16 Comp6: Raspberry pi (olika OS hela tiden)
Phone: Motorola Google Nexus 6

Permalänk
Medlem
Skrivet av Mejan:

Jag har inte läst igenom orda grant nu i din samba fil, men jag ser inget om någon utdelning där. Sedan vill jag även tillägga att jag har aldrig fått fildelning att funka från ubuntu till win genom att höger klicka på mappen i ubuntu.

Här är ett gui program som kan hjälpa dig sätta up allt.

sudo apt-get install system-config-samba

sök bara efter samba när det är installerat så ska du hitta den.

Jag har testat det gui programmet också. Om jag delar via det ser jag mappen i win8 datorn men kan inte komma åt det, "Det går inte att komma åt....etc"

Det är nånting med rättigheterna som strular antar jag?

Permalänk
Medlem

Har du sudo chmod +775 på mappen du ska använda?

Visa signatur

.:Cpu:. AMD Ryzen 9 5950x 3.4GHz:. .:Motherbord:. Asus ROG strix X570-I .:Ram:. 32 GB .:SSD M.2 1TB .:Gpu:.ASUS GeForce RTX 2070 SUPER 8GB ROG STRIX GAMING OC 2560 x 1440 (144Hz), .:OS:. Windows 10 Pro 64-bit .:Chassi:. BitFenix Prodigy M .:Skräm:. Main Acer 24" Predator XB241YU Second Viewsonic VX2268wm 120Hz

Permalänk
Medlem
Skrivet av DwarF:

Har du sudo chmod +775 på mappen du ska använda?

Nej.

Hur skall jag skriva för att det skall funka? Körde blkid för att kolla vad diskarna hette. Mappen jag vill komma åt heter Testmapp1 och ligger på dev//sda1/.

Detta funkar ju ej:

sudo chmod 775 /dev/sda1/Testmapp1/

Få detta då:
"chmod: kan inte komma åt ”/dev/sda1/Testmapp1/”: Inte en katalog"

Permalänk
Medlem

Tror DwarF är på rätt spår. Den här linken går igenom lite rättighets problem som jag hade en gång. Men om det är nåt annat får du gärna säga vad det står i windows när du försöker öppna mappen.

Snabb googling gav mig detta också kanske är intresant.

Visa signatur

Смерть -это решение всех проблем. Нет человека - нет проблемы
Comp1: Ubuntu 16.04 Comp2: Arch Linux
Comp3: Ubuntu Server 16.04 Comp4: Centos 6.5
Comp5: Linux mint 16 Comp6: Raspberry pi (olika OS hela tiden)
Phone: Motorola Google Nexus 6

Permalänk
Medlem
Skrivet av kex:

Nej.

Hur skall jag skriva för att det skall funka? Körde blkid för att kolla vad diskarna hette. Mappen jag vill komma åt heter Testmapp1 och ligger på dev//sda1/.

Detta funkar ju ej:

sudo chmod 775 /dev/sda1/Testmapp1/

Få detta då:
"chmod: kan inte komma åt ”/dev/sda1/Testmapp1/”: Inte en katalog"

du måste montera disken först.

Permalänk
Medlem
Skrivet av mattoys:

du måste montera disken först.

den är monterad.

Permalänk
Medlem
Skrivet av Mejan:

Tror DwarF är på rätt spår. Den här linken går igenom lite rättighets problem som jag hade en gång. Men om det är nåt annat får du gärna säga vad det står i windows när du försöker öppna mappen.

Snabb googling gav mig detta också kanske är intresant.

Tack ska kolla genom länken!

Redan kollat den tråden och testat men det ger samma fel.

Det som händer är när jag klickar på mappen från windows:

"Det går inte att komma åt \\HTPC\Media1\
Kontrollera att namnet inte är felstavat...osv"

Media1 är alltså labeln på disken där jag delar ut mappen "Testmapp1". Jag ser som sagt mappen i windows så utdelningen verkar funka, men rättigheterna stular.

Jag testade även detta utan resultat:
Kom på att disken var formaterad med nfts från win. Och eftersom delade mappar från systemdisken med ubuntu funkar att komma åt så tänkte jag att felet låt här. Så testade formatera från ubuntu istället men samma fel.

Permalänk
Medlem

Jag tror att mattoys menar att du måste montera den virtuellt.

sudo mkdir /vart/du/vill/lägga/den/
sudo mount /dev/sda1/ /vart/du/vill/lägga/den/
sudo chmod 775 /vart/du/vill/lägga/den/

När jag gjorde så fick jag det att funka. Monterade alla diskar i min home mapp, inte så smart kanske.

Visa signatur

Intel i7-5820k .:. 32GB DDR4 2400 MHz .:. RTX 3060 Ti .:. 1TB 970 EVO NVMe .:. AOC 49" 5120x1440@120Hz
Intel E3-1230v2 .:. 32GB DDR3 ECC .:. GTX 1650 .:. 9x3TB WD Red & 4x10TB IronWolf

Permalänk
Medlem
Skrivet av kex:

Nej.

Hur skall jag skriva för att det skall funka? Körde blkid för att kolla vad diskarna hette. Mappen jag vill komma åt heter Testmapp1 och ligger på dev//sda1/.

Detta funkar ju ej:

sudo chmod 775 /dev/sda1/Testmapp1/

Få detta då:
"chmod: kan inte komma åt ”/dev/sda1/Testmapp1/”: Inte en katalog"

Skrivet av kex:

den är monterad.

Fast den är inte monterad där.
Skriv "sudo mount" (eller utan sudo beroende på), för att se en lista på monterade diskar. blkid visar hårdvaruadresser.

Exempeloutput på "mount":
/dev/sda1 on /någon/adress type ext4
eller liknande.

Isf kör du chmod -R 'u=rwx,g=rwx,o=rx' /någon/adress
-R om du vill att den ska rekursivt ändra behörighet på hela disken (ie underkataloger). Behörigheterna blir således read/write/execute på user och group, och read/execute på alla andra. Ändra efter behag.

Permalänk
Medlem
Skrivet av pars:

Jag tror att mattoys menar att du måste montera den virtuellt.

sudo mkdir /vart/du/vill/lägga/den/
sudo mount /dev/sda1/ /vart/du/vill/lägga/den/
sudo chmod 775 /vart/du/vill/lägga/den/

När jag gjorde så fick jag det att funka. Monterade alla diskar i min home mapp, inte så smart kanske.

Yes detta gjorde susen.

Saknade även usershare owner only = false i smb.conf.

Tack för hjälpen alla!

Trevlig sommar!

/erik