WPA i Debian
Hej,
försöker få mitt trådlösa nätverk att fungera i Debian. Kör med WPA-PSK och det vill sig inte alls. Har installerat WPA_supplicant och det är där det verkar strula. Nätverkskortet är ett inbyggt Intel PRO/Wireless 2200 och datorn en fujitsu-siemens amilo m laptop. Kortet verkar fungera för den hittar andra accesspunkter förutom den jag har specificerat i configen.
Tack på förhand.
Min config för wpa_supplicant är:
ctrl_interface=/var/run/wpa_supplicant
ap_scan=2
network={
ssid="Pimpmagic"
scan_ssid=1
proto=WPA
key_mgmt=WPA-PSK
pairwise=TKIP
psk="mittlosenord"
}
Loggen från wpa_supplicant
kirst:/home/jonas# wpa_supplicant -i eth2 -c /etc/wpa_supplicant.conf -D ipw -w -dd
Initializing interface 'eth2' conf '/etc/wpa_supplicant.conf' driver 'ipw' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ap_scan=2
Line: 4 - start of a new network block
ssid - hexdump_ascii(len=9):
50 69 6d 70 6d 61 67 69 63 Pimpmagic
scan_ssid=1 (0x1)
proto: 0x1
key_mgmt: 0x2
pairwise: 0x8
PSK (ASCII passphrase) - hexdump_ascii(len=13): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Line 11: removed CCMP from group cipher list since it was not allowed for pairwise cipher
Priority group 0
id=0 ssid='Pimpmagic'
Initializing interface (2) 'eth2'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_ipw_init is called
SIOCGIWRANGE: WE(compiled)=20 WE(source)=18 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:0e:35:3b:a5:64
wpa_driver_ipw_set_wpa: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
wpa_driver_ipw_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_countermeasures: enabled=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting scan request: 0 sec 100000 usec
Added interface eth2
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added
State: DISCONNECTED -> SCANNING
Trying to associate with SSID 'Pimpmagic'
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
wpa_driver_ipw_set_auth_alg: auth_alg=0x1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
WPA: No WPA/RSN IE available from association info
WPA: Set cipher suites based on configuration
WPA: Selected cipher suites: group 14 pairwise 8 key_mgmt 2 proto 1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting authentication timeout: 60 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b1a len=18
Authentication with 00:00:00:00:00:00 timed out.
Added BSSID 00:00:00:00:00:00 into blacklist
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Trying to associate with SSID 'Pimpmagic'
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
wpa_driver_ipw_set_auth_alg: auth_alg=0x1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
WPA: No WPA/RSN IE available from association info
WPA: Set cipher suites based on configuration
WPA: Selected cipher suites: group 14 pairwise 8 key_mgmt 2 proto 1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting authentication timeout: 60 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b1a len=18
