Vill du vara del av diskussionerna i forumet, ställa frågor eller hjälpa andra? Registrera dig här!

Önskar få hjälp att få igång mobilt bredband via router

Trädvy Permalänk
Medlem
Registrerad
Dec 2012

Önskar få hjälp att få igång mobilt bredband via router

Hej,

Jag försöker få till en intenetuppkoppling via dongel i router, men får inte till det

Har en D-Link DWM-222 med ett Halebop simkort utan pin i och en nyss fabriksåterställd Asus RT-AC51U med senaste firmware. När jag kopplat in grejerna och försökt konfa routern så ser allt bra ut, men jag kommer inte ut på internet.

Network map säger att jag är connected och jag får en WAN IP.

och Windows tycker att jag har internetåtkomst.

Men "jordgloben" på routern är släckt.

Modemet blikar grönt. "Green (blinking): Connected to LTE network"

USB-inställningarna. Kanske något är fel/saknas här?

Har stängt av Dual LAN.

Router har fel datum/tid pga ej kontakt med tidsserver. Kopplade in fibern i router och fick den då att ställa in tiden korrekt, men när jag kopplade bort fibern så återställdes den till 2015 igen. Jag har för mig att en felaktig datum/tid kan spärra mobila uppkopplingar? Men den går inte att ställa manuellt och sabbar sig själv när den inte kommer åt internet tycks det.

Övriga statusar ser bra ut:

Bifogar loggen i ett svar till posten.

Tacksam för hjälp!

Trädvy Permalänk
Medlem
Registrerad
Dec 2012

Feb 11 19:58:29 WAN Connection: Ethernet link down.
Feb 11 19:58:29 stop_nat_rules: apply the redirect_rules!
Feb 11 19:58:31 rc_service: httpd 208:notify_rc reboot
Feb 11 19:58:31 pppd[1950]: Connection terminated.
Feb 11 19:58:32 pppd[1950]: Child process /bin/comgt -d /dev/ttyUSB1 -s /etc/ppp/3g/Generic_disconn.scr (pid 15542) terminated with signal 15
Feb 11 19:58:32 pppd[1950]: disconnect script failed
Feb 11 19:58:33 FTP Server: daemon is stoped
Feb 11 19:58:33 Samba Server: smb daemon is stoped
Feb 11 19:58:33 WEBDAV Server: daemon is stoped
Feb 11 19:58:34 WEBDAV Server: daemon is stoped
Feb 11 19:58:34 FTP Server: daemon is stoped
Feb 11 19:58:34 Samba Server: smb daemon is stoped
Feb 11 19:58:34 miniupnpd[7000]: shutting down MiniUPnPd
Feb 11 19:58:36 kernel: klogd: exiting
Feb 11 19:58:36 syslogd exiting
Aug 1 02:00:15 syslogd started: BusyBox v1.17.4
Aug 1 02:00:15 kernel: klogd started: BusyBox v1.17.4 (2018-03-20 09:18:33 CST)
Aug 1 02:00:15 kernel: Linux version 2.6.36 (root@asus) (gcc version 4.2.4) #1 Tue Mar 20 09:21:08 CST 2018
Aug 1 02:00:15 kernel: The CPU feqenuce set to 580 MHz
Aug 1 02:00:15 kernel: PCIE: bypass PCIe DLL.
Aug 1 02:00:15 kernel: PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
Aug 1 02:00:15 kernel: disable all power about PCIe
Aug 1 02:00:15 kernel: Zone PFN ranges:
Aug 1 02:00:15 kernel: Normal 0x00000000 -> 0x00004000
Aug 1 02:00:15 kernel: Movable zone start PFN for each node
Aug 1 02:00:15 kernel: early_node_map[1] active PFN ranges
Aug 1 02:00:15 kernel: 0: 0x00000000 -> 0x00004000
Aug 1 02:00:15 kernel: Built 1 zonelists in Zone order, mobility grouping off. Total pages: 16256
Aug 1 02:00:15 kernel: Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock4 rootfstype=squashfs
Aug 1 02:00:15 kernel: Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Aug 1 02:00:15 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Aug 1 02:00:15 kernel: init_r4k_clocksource: cpu_has_counter(128) mips_hpt_frequency(290000000)
Aug 1 02:00:15 kernel: new mips_hpt_frequency(289260310)
Aug 1 02:00:15 kernel: Mount-cache hash table entries: 512
Aug 1 02:00:15 kernel: RALINK_GPIOMODE = 1a311d
Aug 1 02:00:15 kernel: RALINK_GPIOMODE = 18311d
Aug 1 02:00:15 kernel: PPLL_CFG1=0xe70000
Aug 1 02:00:15 kernel: MT7620 PPLL lock
Aug 1 02:00:15 kernel: PPLL_DRV =0x80080504
Aug 1 02:00:15 kernel: start PCIe register access
Aug 1 02:00:15 kernel: RALINK_RSTCTRL = 2400000
Aug 1 02:00:15 kernel: RALINK_CLKCFG1 = 75afffc0
Aug 1 02:00:15 kernel: *************** MT7620 PCIe RC mode *************
Aug 1 02:00:15 kernel: PCIE0 enabled
Aug 1 02:00:15 kernel: init_rt2880pci done
Aug 1 02:00:15 kernel: bio: create slab <bio-0> at 0
Aug 1 02:00:15 kernel: BAR0 at slot 0 = 0
Aug 1 02:00:15 kernel: bus=0x0, slot = 0x0
Aug 1 02:00:15 kernel: res[0]->start = 0
Aug 1 02:00:15 kernel: res[0]->end = 0
Aug 1 02:00:15 kernel: res[1]->start = 20200000
Aug 1 02:00:15 kernel: res[1]->end = 2020ffff
Aug 1 02:00:15 kernel: res[2]->start = 0
Aug 1 02:00:15 kernel: res[2]->end = 0
Aug 1 02:00:15 kernel: res[3]->start = 0
Aug 1 02:00:15 kernel: res[3]->end = 0
Aug 1 02:00:15 kernel: res[4]->start = 0
Aug 1 02:00:15 kernel: res[4]->end = 0
Aug 1 02:00:15 kernel: res[5]->start = 0
Aug 1 02:00:15 kernel: res[5]->end = 0
Aug 1 02:00:15 kernel: bus=0x1, slot = 0x0
Aug 1 02:00:15 kernel: res[0]->start = 20000000
Aug 1 02:00:15 kernel: res[0]->end = 200fffff
Aug 1 02:00:15 kernel: res[1]->start = 0
Aug 1 02:00:15 kernel: res[1]->end = 0
Aug 1 02:00:15 kernel: res[2]->start = 0
Aug 1 02:00:15 kernel: res[2]->end = 0
Aug 1 02:00:15 kernel: res[3]->start = 0
Aug 1 02:00:15 kernel: res[3]->end = 0
Aug 1 02:00:15 kernel: res[4]->start = 0
Aug 1 02:00:15 kernel: res[4]->end = 0
Aug 1 02:00:15 kernel: res[5]->start = 0
Aug 1 02:00:15 kernel: res[5]->end = 0
Aug 1 02:00:15 kernel: bus=0x1, slot = 0x0
Aug 1 02:00:15 kernel: res[0]->start = 20100000
Aug 1 02:00:15 kernel: res[0]->end = 201fffff
Aug 1 02:00:15 kernel: res[1]->start = 0
Aug 1 02:00:15 kernel: res[1]->end = 0
Aug 1 02:00:15 kernel: res[2]->start = 0
Aug 1 02:00:15 kernel: res[2]->end = 0
Aug 1 02:00:15 kernel: res[3]->start = 0
Aug 1 02:00:15 kernel: res[3]->end = 0
Aug 1 02:00:15 kernel: res[4]->start = 0
Aug 1 02:00:15 kernel: res[4]->end = 0
Aug 1 02:00:15 kernel: res[5]->start = 0
Aug 1 02:00:15 kernel: res[5]->end = 0
Aug 1 02:00:16 kernel: Load Ralink Timer0 Module
Aug 1 02:00:16 kernel: Load Ralink Timer1 Module
Aug 1 02:00:16 kernel: RT3xxx EHCI/OHCI init.
Aug 1 02:00:16 kernel: Ralink gpio driver initialized
Aug 1 02:00:16 kernel: Ralink SPI flash driver, SPI clock: 48MHz
Aug 1 02:00:16 kernel: deice id : 1 20 18 4d 1 (20184d01)
Aug 1 02:00:16 kernel: S25FL129P(01 20184d01) (16384 Kbytes)
Aug 1 02:00:16 kernel: mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Aug 1 02:00:16 kernel: partion 3: ffffffff eb0000
Aug 1 02:00:16 kernel: partion 4: 16ee40 d911c0
Aug 1 02:00:16 kernel: #add mtd partition#
Aug 1 02:00:16 kernel: Creating 7 MTD partitions on "raspi":
Aug 1 02:00:16 kernel: 0x000000000000-0x000000030000 : "Bootloader"
Aug 1 02:00:16 kernel: 0x000000030000-0x000000040000 : "nvram"
Aug 1 02:00:16 kernel: 0x000000040000-0x000000050000 : "Factory"
Aug 1 02:00:16 kernel: 0x000000050000-0x000000f00000 : "linux"
Aug 1 02:00:16 kernel: 0x00000016ee40-0x000000f00000 : "rootfs"
Aug 1 02:00:16 kernel: 0x000000f00000-0x000001000000 : "jffs2"
Aug 1 02:00:16 kernel: 0x000000000000-0x000001000000 : "ALL"
Aug 1 02:00:16 kernel: rdm_major = 253
Aug 1 02:00:16 kernel: Allocate 4096 entries coherent memory for hw_nat. (262144 bytes)
Aug 1 02:00:16 kernel: SMACCR1 -- : 0x00002c56
Aug 1 02:00:16 kernel: SMACCR0 -- : 0xdc469c88
Aug 1 02:00:16 kernel: Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500!
Aug 1 02:00:16 kernel: SMACCR1 -- : 0x00002c56
Aug 1 02:00:16 kernel: SMACCR0 -- : 0xdc469c88
Aug 1 02:00:16 kernel: PROC INIT OK!
Aug 1 02:00:16 kernel: matchsize=262
Aug 1 02:00:16 kernel: gre: can't add protocol
Aug 1 02:00:16 kernel: SQUASHFS error: Xattrs in filesystem, these will be ignored
Aug 1 02:00:16 kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Aug 1 02:00:16 kernel: offset 0x1000 elapse 0ms
Aug 1 02:00:16 kernel: Algorithmics/MIPS FPU Emulator v1.5
Aug 1 02:00:16 kernel: bled: GPIO#14: USB BUS mask 3.
Aug 1 02:00:16 kernel: rt2860v2_ap: module license 'Proprietary' taints kernel.
Aug 1 02:00:16 kernel: Disabling lock debugging due to kernel taint
Aug 1 02:00:16 kernel: rt2860v2:
Aug 1 02:00:16 kernel: === pAd = c0542000, size = 830272 ===
Aug 1 02:00:16 kernel: <-- RTMPAllocTxRxRingMemory, Status=0
Aug 1 02:00:16 kernel: <-- RTMPAllocAdapterBlock, Status=0
Aug 1 02:00:16 kernel: rt2860v2:AP Driver version-2.7.2.0_edcca_monitor_20131222
Aug 1 02:00:16 kernel: MT7610ap:register rtpci
Aug 1 02:00:16 kernel: MT7610ap:
Aug 1 02:00:16 kernel: === pAd = c0b02000, size = 1074344 ===
Aug 1 02:00:16 kernel: <-- RTMPAllocTxRxRingMemory, Status=0
Aug 1 02:00:17 kernel: <-- RTMPAllocAdapterBlock, Status=0
Aug 1 02:00:17 kernel: MT7610ap:pAd->CSRBaseAddress =0xc0a00000, csr_addr=0xc0a00000!
Aug 1 02:00:17 kernel: MT7610ap:device_id =0x7650
Aug 1 02:00:17 kernel: MT7610ap:==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
Aug 1 02:00:17 kernel: MT7610ap:MACVersion = 0x76502000
Aug 1 02:00:17 kernel: Raeth v3.1 (Tasklet,SkbRecycle)
Aug 1 02:00:17 kernel: phy_tx_ring = 0x02c8a000, tx_ring = 0xa2c8a000
Aug 1 02:00:17 kernel: phy_rx_ring0 = 0x02d30000, rx_ring0 = 0xa2d30000
Aug 1 02:00:17 kernel: SMACCR1 -- : 0x00002c56
Aug 1 02:00:17 kernel: SMACCR0 -- : 0xdc469c8c
Aug 1 02:00:17 kernel: ESW: Link Status Changed - LAN1 (P1) Link DOWN
Aug 1 02:00:17 kernel: CDMA_CSG_CFG = 81000000
Aug 1 02:00:17 kernel: GDMA1_FWD_CFG = 20710000
Aug 1 02:00:17 kernel: rt2860v2:RX DESC a33cf000 size = 2048
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[0]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[1]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[2]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[3]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[4]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[5]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[6]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[7]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[8]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[9]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[10]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[11]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[12]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[13]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[14]=1
Aug 1 02:00:17 kernel: rt2860v2:APSDCapable[15]=1
Aug 1 02:00:17 kernel: rt2860v2:pAd->ed_chk = 1
Aug 1 02:00:17 kernel: rt2860v2:Key1Str is Invalid key length(0) or Type(0)
Aug 1 02:00:17 kernel: rt2860v2:Key2Str is Invalid key length(0) or Type(0)
Aug 1 02:00:17 kernel: rt2860v2:Key3Str is Invalid key length(0) or Type(0)
Aug 1 02:00:17 kernel: rt2860v2:Key4Str is Invalid key length(0) or Type(0)
Aug 1 02:00:17 kernel: rt2860v2:RTMPSetDefaultChannel() : default channel to 1
Aug 1 02:00:17 kernel: rt2860v2:1. Phy Mode = 9
Aug 1 02:00:17 kernel: rt2860v2:2. Phy Mode = 9
Aug 1 02:00:17 kernel: rt2860v2:E2PROM: D0 target power=0xff24
Aug 1 02:00:17 kernel: rt2860v2:E2PROM: 40 MW Power Delta= 1
Aug 1 02:00:17 kernel: rt2860v2:3. Phy Mode = 9
Aug 1 02:00:17 kernel: rt2860v2:^[[mAntCfgInit: primary/secondary ant 0/1
Aug 1 02:00:17 kernel: ^[[mrt2860v2:Initialize RF Central Registers for E2 !!!
Aug 1 02:00:17 kernel: rt2860v2:Initialize RF Central Registers for E3 !!!
Aug 1 02:00:17 kernel: rt2860v2:Initialize RF Channel Registers for E2 !!!
Aug 1 02:00:17 kernel: rt2860v2:Initialize RF Channel Registers for E3 !!!
Aug 1 02:00:17 kernel: rt2860v2:Initialize RF DCCal Registers for E2 !!!
Aug 1 02:00:17 kernel: rt2860v2:Initialize RF DCCal Registers for E3 !!!
Aug 1 02:00:17 kernel: rt2860v2:D1 = -1, D2 = 10, CalCode = 26 !!!
Aug 1 02:00:17 kernel: rt2860v2:RT6352_Temperature_Init : BBPR49 = 0xffffffff
Aug 1 02:00:17 kernel: rt2860v2:RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5
Aug 1 02:00:17 kernel: rt2860v2:Current Temperature from BBP_R49=0xfffffffa
Aug 1 02:00:17 kernel: rt2860v2:RT6352_TssiTableAdjust: upper_bound = 0x7F decimal: 127
Aug 1 02:00:17 kernel: rt2860v2:RT6352_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
Aug 1 02:00:17 kernel: rt2860v2:*** RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -128 -128 -128 -22 -14 -7
Aug 1 02:00:17 kernel: - 0 - 13 22 28 127 127 127 127, offset=-11, tuning=1
Aug 1 02:00:17 kernel: rt2860v2:RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -128 -128 -128 -33 -25 -18 - -11 - 2 11 17 116 116 116 116, offset=-11, tuning=1
Aug 1 02:00:17 kernel: rt2860v2:mp_temperature=0xffffffff, step = +0
Aug 1 02:00:17 kernel: rt2860v2:E2PROM: G Tssi[-7 .. +7] = -128 -128 -128 -128 -33 -25 -18 - -11 - 2 11 17 116 116 116 116, offset=-11, tuning=1
Aug 1 02:00:17 kernel: rt2860v2: TX BW Filter Calibration !!!
Aug 1 02:00:17 kernel: rt2860v2: RX BW Filter Calibration !!!
Aug 1 02:00:17 kernel: rt2860v2:LOFT Calibration Done!
Aug 1 02:00:18 kernel: rt2860v2:IQCalibration Start!
Aug 1 02:00:18 kernel: rt2860v2:IQCalibration Done! CH = 0, (gain= 1, phase=3d)
Aug 1 02:00:18 kernel: rt2860v2:IQCalibration Start!
Aug 1 02:00:18 kernel: rt2860v2:IQCalibration Done! CH = 1, (gain= d, phase=3f)
Aug 1 02:00:18 kernel: rt2860v2:TX IQ Calibration Done!
Aug 1 02:00:18 kernel: rt2860v2:Set_DyncVgaEnable_Proc::(enable = 0)
Aug 1 02:00:18 kernel: rt2860v2:bAutoTxAgcG = 1
Aug 1 02:00:18 kernel: rt2860v2:MCS Set = ff ff 00 00 01
Aug 1 02:00:18 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug 1 02:00:20 kernel: ch1 bssid=e0:b9:e5:d4:79:a3
Aug 1 02:00:20 kernel: ch1 bssid=10:13:31:ab:cc:09
Aug 1 02:00:20 kernel: ch6 bssid=e4:6f:13:59:52:50
Aug 1 02:00:20 kernel: ch6 bssid=9c:97:26:cb:5a:fb
Aug 1 02:00:20 kernel: ch8 bssid=de:4f:22:49:7a:61
Aug 1 02:00:20 kernel: ch8 bssid=50:c7:bf:45:dd:74
Aug 1 02:00:20 kernel: ch10 bssid=4c:ed:fb:c2:f5:51
Aug 1 02:00:20 kernel: ch11 bssid=14:59:c0:8c:8e:ca
Aug 1 02:00:20 kernel: =====================================================
Aug 1 02:00:20 kernel: Channel 1 : Dirty = 140, False CCA = 38, Busy Time = 4313, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 2 : Dirty = 104, False CCA = 25, Busy Time = 1073, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 3 : Dirty = 104, False CCA = 7, Busy Time = 136, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 4 : Dirty = 144, False CCA = 19, Busy Time = 284, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 5 : Dirty = 152, False CCA = 9, Busy Time = 269, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 6 : Dirty = 216, False CCA = 94, Busy Time = 3970, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 7 : Dirty = 172, False CCA = 34, Busy Time = 2372, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 8 : Dirty = 248, False CCA = 58, Busy Time = 2881, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 9 : Dirty = 172, False CCA = 6, Busy Time = 57, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 10 : Dirty = 198, False CCA = 5, Busy Time = 3717, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 11 : Dirty = 150, False CCA = 26, Busy Time = 2543, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 12 : Dirty = 100, False CCA = 6, Busy Time = 128, Skip Channel = FALSE
Aug 1 02:00:20 kernel: Channel 13 : Dirty = 52, False CCA = 25, Busy Time = 255, Skip Channel = FALSE
Aug 1 02:00:20 kernel: =====================================================
Aug 1 02:00:20 kernel: Rule 1 CCA value : Min Dirtiness (Include extension channel) ==> Select Channel 13
Aug 1 02:00:20 kernel: Min Dirty = 224
Aug 1 02:00:20 kernel: ExChannel = 9 , 0
Aug 1 02:00:20 kernel: BW = 40
Aug 1 02:00:20 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug 1 02:00:20 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug 1 02:00:20 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug 1 02:00:21 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug 1 02:00:21 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug 1 02:00:21 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug 1 02:00:22 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug 1 02:00:22 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug 1 02:00:22 kernel: rt2860v2:@@@ ed_monitor_init : ===>
Aug 1 02:00:22 kernel: rt2860v2:@@@ ed_monitor_init : <===
Aug 1 02:00:22 kernel: rt2860v2:Main bssid = 2c:56:dc:46:9c:88
Aug 1 02:00:22 kernel: <==== rt28xx_init, Status=0
Aug 1 02:00:22 kernel: 0x1300 = 00064300
Aug 1 02:00:22 kernel: rt2860v2:@@@ ed_monitor_init : ===>
Aug 1 02:00:22 kernel: rt2860v2:@@@ ed_monitor_init : <===
Aug 1 02:00:23 kernel: load fw spent 16ms
Aug 1 02:00:23 kernel: MT7610ap:RX DESC a2a63000 size = 2048
Aug 1 02:00:23 kernel: MT7610ap:RX1 DESC a2a70000 size = 2048
Aug 1 02:00:23 kernel: MT7610ap:cfg_mode=14
Aug 1 02:00:23 kernel: MT7610ap:cfg_mode=14
Aug 1 02:00:23 kernel: MT7610ap:wmode_band_equal(): Band Not Equal!
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[0]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[1]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[2]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[3]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[4]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[5]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[6]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[7]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[8]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[9]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[10]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[11]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[12]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[13]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[14]=1
Aug 1 02:00:23 kernel: MT7610ap:APSDCapable[15]=1
Aug 1 02:00:23 kernel: MT7610ap:pAd->ed_chk = 1
Aug 1 02:00:23 kernel: MT7610ap:Key1Str is Invalid key length(0) or Type(0)
Aug 1 02:00:23 kernel: MT7610ap:Key2Str is Invalid key length(0) or Type(0)
Aug 1 02:00:23 kernel: MT7610ap:Key3Str is Invalid key length(0) or Type(0)
Aug 1 02:00:23 kernel: MT7610ap:Key4Str is Invalid key length(0) or Type(0)
Aug 1 02:00:23 kernel: MT7610ap:1. Phy Mode = 49
Aug 1 02:00:23 kernel: MT7610ap:2. Phy Mode = 49
Aug 1 02:00:23 kernel: drivers/net/wireless/MT7610_ap/./chips/mt76x0.c:2419 assert (pAd->TxPower[choffset].Channel == 149)failed
Aug 1 02:00:23 kernel: drivers/net/wireless/MT7610_ap/./chips/mt76x0.c:2436 assert (pAd->TxPower[choffset].Channel == 42)failed
Aug 1 02:00:23 kernel: MT7610ap:ext_pa_current_setting = 1
Aug 1 02:00:23 kernel: MT7610ap:MT76x0_TssiTableAdjust: upper_bound = 0x7F decimal: 127
Aug 1 02:00:23 kernel: MT7610ap:MT76x0_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
Aug 1 02:00:23 kernel: MT7610ap:*** MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -14 -8 -4 * 0 * 2 6 8 127 127 127 127, offset=-6, tuning=1
Aug 1 02:00:23 kernel: MT7610ap:MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -20 -14 -10 * -6 * -4 0 2 121 121 121 121, offset=-6, tuning=1
Aug 1 02:00:23 kernel: MT7610ap:mp_temperature=0xffffffff, step = +1
Aug 1 02:00:23 kernel: MT7610ap:MT76x0_TssiTableAdjust: upper_bound = 0x7F decimal: 127
Aug 1 02:00:23 kernel: MT7610ap:MT76x0_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
Aug 1 02:00:23 kernel: MT7610ap:*** MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -13 -9 -4 * -6 * 2 5 8 127 127 127 127, offset=-6, tuning=1
Aug 1 02:00:23 kernel: MT7610ap:MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -19 -15 -10 * -6 * -4 -1 2 121 121 121 121, offset=-6, tuning=1
Aug 1 02:00:23 kernel: MT7610ap:mp_temperature=0xffffffff, step = +1
Aug 1 02:00:23 kernel: MT7610ap:3. Phy Mode = 49
Aug 1 02:00:23 kernel: MT7610ap:AntCfgInit: primary/secondary ant 0/1
Aug 1 02:00:23 kernel: MT7610ap:ChipStructAssign(): RALINK6590 hook !
Aug 1 02:00:23 kernel: MT7610ap:bAutoTxAgcG = 1
Aug 1 02:00:23 kernel: MT7610ap:@@@ BuildChannel # 36 :: Pwr0 = 29, Pwr1 =0, Flags = c0, RemainingTimeForUse=0
Aug 1 02:00:23 kernel: MT7610ap:@@@ BuildChannel # 40 :: Pwr0 = 29, Pwr1 =0, Flags = c0, RemainingTimeForUse=0
Aug 1 02:00:23 kernel: MT7610ap:@@@ BuildChannel # 44 :: Pwr0 = 28, Pwr1 =0, Flags = c0, RemainingTimeForUse=0
Aug 1 02:00:23 kernel: MT7610ap:@@@ BuildChannel # 48 :: Pwr0 = 28, Pwr1 =0, Flags = c0, RemainingTimeForUse=0
Aug 1 02:00:23 kernel: MT7610ap:RTMPSetPhyMode: channel is out of range, use first channel=0
Aug 1 02:00:23 kernel: MT7610ap:MCS Set = ff 00 00 00 01
Aug 1 02:00:23 kernel: MT7610ap:MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
Aug 1 02:00:23 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:23 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:23 kernel: MT7610ap: result [0]!!
Aug 1 02:00:23 kernel: MT7610ap:APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
Aug 1 02:00:23 kernel: MT7610ap:LOG#0 2c:56:dc:46:9c:8c restart access point
Aug 1 02:00:23 kernel: MT7610ap:@@@ ed_monitor_init : ===>
Aug 1 02:00:23 kernel: MT7610ap:@@@ ed_monitor_init : <===
Aug 1 02:00:23 kernel: MT7610ap:Main bssid = 2c:56:dc:46:9c:8c
Aug 1 02:00:23 kernel: <==== rt28xx_init, Status=0
Aug 1 02:00:25 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:25 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:25 kernel: MT7610ap: result [0]!!
Aug 1 02:00:25 kernel: MT7610ap:FullCalibration(): docal = [0000] valid bit[0]
Aug 1 02:00:25 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:25 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:25 kernel: MT7610ap: result [0]!!
Aug 1 02:00:25 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:25 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:25 kernel: MT7610ap: result [0]!!
Aug 1 02:00:25 kernel: MT7610ap:FullCalibration(): docal = [0000] valid bit[0]
Aug 1 02:00:25 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:25 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:25 kernel: MT7610ap: result [0]!!
Aug 1 02:00:25 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:25 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:25 kernel: MT7610ap: result [0]!!
Aug 1 02:00:25 kernel: MT7610ap:FullCalibration(): docal = [0000] valid bit[0]
Aug 1 02:00:25 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:25 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:25 kernel: MT7610ap: result [0]!!
Aug 1 02:00:25 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:26 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:26 kernel: MT7610ap: result [0]!!
Aug 1 02:00:26 kernel: MT7610ap:FullCalibration(): docal = [0000] valid bit[0]
Aug 1 02:00:26 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:26 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:26 kernel: MT7610ap: result [0]!!
Aug 1 02:00:26 kernel: MT7610ap:SYNC - BBP R4 to 20MHz.l
Aug 1 02:00:26 kernel: MT7610ap:FullCalibration(): docal = [0000] valid bit[0]
Aug 1 02:00:26 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:26 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:26 kernel: MT7610ap: result [0]!!
Aug 1 02:00:26 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:26 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:26 kernel: MT7610ap: result [0]!!
Aug 1 02:00:26 kernel: MT7610ap:FullCalibration(): docal = [0000] valid bit[0]
Aug 1 02:00:26 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:26 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:26 kernel: MT7610ap: result [0]!!
Aug 1 02:00:26 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:26 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:26 kernel: MT7610ap: result [0]!!
Aug 1 02:00:26 kernel: MT7610ap:FullCalibration(): docal = [0000] valid bit[0]
Aug 1 02:00:26 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:26 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:26 kernel: MT7610ap: result [0]!!
Aug 1 02:00:26 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:26 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:26 kernel: MT7610ap: result [0]!!
Aug 1 02:00:26 kernel: MT7610ap:FullCalibration(): docal = [0000] valid bit[0]
Aug 1 02:00:26 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:26 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:26 kernel: MT7610ap: result [0]!!
Aug 1 02:00:26 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:26 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:26 kernel: MT7610ap: result [0]!!
Aug 1 02:00:26 kernel: ch36 bssid=50:c7:bf:45:dd:73
Aug 1 02:00:26 kernel: =====================================================
Aug 1 02:00:26 kernel: Channel 36 : Dirty = 70, False CCA = 89, Busy Time = 848, Skip Channel = FALSE
Aug 1 02:00:26 kernel: Channel 40 : Dirty = 32, False CCA = 0, Busy Time = 634, Skip Channel = FALSE
Aug 1 02:00:26 kernel: Channel 44 : Dirty = 0, False CCA = 25, Busy Time = 173, Skip Channel = FALSE
Aug 1 02:00:27 kernel: Channel 48 : Dirty = 0, False CCA = 570, Busy Time = 2714, Skip Channel = FALSE
Aug 1 02:00:27 kernel: =====================================================
Aug 1 02:00:27 kernel: Extcha(above)
Aug 1 02:00:27 kernel: Rule 1 CCA value : Min Dirtiness (Include extension channel) ==> Select Channel 36
Aug 1 02:00:27 kernel: Min Dirty = 102
Aug 1 02:00:27 kernel: ExChannel = 0 , 0
Aug 1 02:00:27 kernel: BW = 40
Aug 1 02:00:27 kernel: BW = 80
Aug 1 02:00:27 kernel: MT7610ap:@@@ APStop: go to ed_monitor_exit()!!
Aug 1 02:00:27 kernel: MT7610ap:@@@ ed_monitor_exit : ===>
Aug 1 02:00:27 kernel: MT7610ap:@@@ ed_monitor_exit : <===
Aug 1 02:00:27 kernel: MT7610ap:MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
Aug 1 02:00:27 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:27 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:27 kernel: MT7610ap: result [0]!!
Aug 1 02:00:27 kernel: MT7610ap:APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
Aug 1 02:00:27 kernel: MT7610ap:LOG#1 2c:56:dc:46:9c:8c restart access point
Aug 1 02:00:27 kernel: MT7610ap:FullCalibration(): docal = [0000] valid bit[0]
Aug 1 02:00:27 kernel: MT7610ap:==== 2C70 [0] ,RXBackup [0]
Aug 1 02:00:27 kernel: MT7610ap: RX Cal =0 , use RXBackup [0] to restore!!
Aug 1 02:00:27 kernel: MT7610ap: result [0]!!
Aug 1 02:00:27 kernel: MT7610ap:@@@ ed_monitor_init : ===>
Aug 1 02:00:27 kernel: MT7610ap:@@@ ed_monitor_init : <===
Aug 1 02:00:27 kernel: 0x1300 = 00064300
Aug 1 02:00:27 kernel: MT7610ap:RTMPDrvOpen(1):Check if PDMA is idle!

Dold text
Trädvy Permalänk
Medlem
Registrerad
Jan 2018

Har du kollat så dongeln stöds av routern?
Jag försökte mig på samma sak med en Huawei-dongel tills jag upptäckte att den inte var med i kompabilitetslistan för min Router

[Edit: Här har du kompatibilitetslistan för Asus routers. Din dongel står inte med så det är nog därför det inte funkar ]

Tillägg

Aorus Elite X570, Ryzen 3700x, G.Skill Trident Z Neo 3600MHz, MSI Rtx 2080 Gaming Trio

Trädvy Permalänk
Medlem
Registrerad
Dec 2012

@Mr Steed: okej, stort tack. Fattade inte att det var nån risk att de var inkompatibla. Frågan är om man ska leta efter en annan dongel eller en annan router då

Edit: eller en router med inbyggt modem/sim-plats. Borde vara smidigast.

Trädvy Permalänk
Medlem
Registrerad
Apr 2019

Kolla hur stödet ser ut med OpenWrt https://openwrt.org/toh/asus/rt-ac51u

Trädvy Permalänk
Medlem
Registrerad
Dec 2012

@CymbalCrasher: tack, jag tror dock jag byter ut dongeln mot en TP-Link Archer MR200 https://www.prisjakt.nu/produkt.php?p=3310258
Jag hade inte köpt Asus-routern utan den hade bara blivit över, så det är ingen förlust

Trädvy Permalänk
Medlem
Plats
Göteborg
Registrerad
Mar 2011

@Biggis:
Både MR200 och MR400 har bara 100 Mbit/s portar.
MR 600 har gigabit portar.
De båda första har 4G Cat4 max 150 Mbit/s, MR 600 har Cat6 300 Mbit/s.

Klient: Intel I7 3820 | ASUS P9X79 Pro | 64GB 1600MHz | Corsair HX 850W | Gigabyte 1080TI | HAF 922 | Crucial 525G | Seagate XT 4TB
Server: Intel XEON E5620 x 2| ASUS Z8PE-D18 | 96GB 1333MHz | Corsair AX 1200W | HAF 932 | WD Black 2TB
HTPC: Intel I7 4770T | 16 GB 1600 | FC8 EVO | Gigabyte GA-H87N-WIFI | Samsung 840 250GB

Trädvy Permalänk
Medlem
Registrerad
Nov 2019
Skrivet av Biggis:

@CymbalCrasher: tack, jag tror dock jag byter ut dongeln mot en TP-Link Archer MR200 https://www.prisjakt.nu/produkt.php?p=3310258
Jag hade inte köpt Asus-routern utan den hade bara blivit över, så det är ingen förlust

Skulle avråda dig från den routern. Prövade den själv och efter en del krångel bytte jag mot en ASUS 4G-AC53U. Kör den idag och kan rekommendera den. Finns säkert bättre men den duger åt mig!

Skickades från m.sweclockers.com

Trädvy Permalänk
Medlem
Plats
Askersund
Registrerad
Jan 2005

MR400 slutade fungera med Tele2 i december, med många rapporter om samma fel med MR200 och MR6400. MR600 verkar dock ha klarat sig. Senaste firmware i januari till dom låser i princip till 3G-hastighet. Kolla upp så det är fixat - jag lämnade tillbaka på garanti efter över en månad utan internet. Nu använder du Halebop (enligt bilder), men man vet ju aldrig om man får för sig att byta operatör i framtiden.

Skickades från m.sweclockers.com

Trädvy Permalänk
Medlem
Registrerad
Dec 2012
Skrivet av Prelatur:

@Biggis:
Både MR200 och MR400 har bara 100 Mbit/s portar.
MR 600 har gigabit portar.
De båda första har 4G Cat4 max 150 Mbit/s, MR 600 har Cat6 300 Mbit/s.

Hej, Tack för svar. Ska den i stugan och endast wifi är aktuellt.

Trädvy Permalänk
Medlem
Registrerad
Dec 2012
Skrivet av nQah:

Skulle avråda dig från den routern. Prövade den själv och efter en del krångel bytte jag mot en ASUS 4G-AC53U. Kör den idag och kan rekommendera den. Finns säkert bättre men den duger åt mig!

Skickades från m.sweclockers.com

Hej, tack för svar! Ja, det känns lite som ett lotteri vad som funkar och inte, åtminston när det gäller donglar. Men det kanske är likadant ned "sim-router". Har beställd en MR200 nu då Webhallen hade den på deal (899kr). Funkar den inte så får jag försäka byta den, och då kanske mot en sån du kör.

Trädvy Permalänk
Medlem
Registrerad
Dec 2012
Skrivet av wh2ne:

MR400 slutade fungera med Tele2 i december, med många rapporter om samma fel med MR200 och MR6400. MR600 verkar dock ha klarat sig. Senaste firmware i januari till dom låser i princip till 3G-hastighet. Kolla upp så det är fixat - jag lämnade tillbaka på garanti efter över en månad utan internet. Nu använder du Halebop (enligt bilder), men man vet ju aldrig om man får för sig att byta operatör i framtiden.

Skickades från m.sweclockers.com

Hej, Tack för svar! Ja, just nu försöker jag kör jag Halebop, tänkte att Telias när borde vara bäst, men nån granne sa att 3 faktiskt funkade bättre för dom så det blir nog att testa det sen.

Förhoppningsvis fungerar denna (MR200) och i skaplig hastighet i alla fall. Men vi får se