NukeHenk:
Alla temperaturer är på IDLE.
Jag har utfört manuella inställningar i BIOS, ser på följande vis (datorn hängde sig i Vista):
MAIN
Legacy Diskette A [Disabled]
On Chip SATA Channel [Enabled]
On Chip SATA Type [IDE]
ADVANCED
JumperFree Configuration
AI Overclocking [Manual]
FSB Frequency [200]
PCIE Frequency [100]
Processor Frequency Multiplier [x12.5 2500MHz]
Processor Voltage [1.3000]
Processor-NB Voltage [1.2000]
CPU VDDA Voltage [2.6v]
Processor-NB Frequency Multiplier [AUTO] Vad ska jag ha på denna?
CPU-NB HT Link Speed [AUTO] - Kan jag ha 1GHZ på denna?
DDR Voltage [2.20]
Northbridge Voltage [Manual]
Hyper Transport Volatge [1.50v]
Core/PCIe Voltage [1.12]
NB PCIE PLL [1.9v]
Southbridge Voltage [1.22]
Auto Xpress [Disabled]
CPU Tweak [Disabled]
Memory Configuration
Bank Interleving [Auto]
Channel Interleaving XOR of Address bits [20:16,6]
MemClk Trisate C3/ATLVID [Disabled]
Memory Hole Remaping [Enabled]
Power Down Enable [Disabled]
Read Delay [1.0 Memory CLKs]
DCQ Bypass Maximum [Auto]
DRAM Timing Configuration
Memory Clock Mode [Manual]
Memory Clock Value [800 MHz]
2T Mode [AUTO]
DRAM Timing Mode [AUTO]
CAS Latency (CL) [AUTO]
TCWL [AUTO]
TRCD [AUTO]
TRP [AUTO]
TRAS [AUTO]
tWR [AUTO]
tRFC0 [AUTO]
tRFC1 [AUTO]
tRFC2 [AUTO]
tRFC3 [AUTO]
TRC [AUTO]
TRRD [AUTO]
tWTR [AUTO]
tRTP [AUTO]
PLL1 Spread Spectrum [Disabled]
PLL2 Spread Spectrum [Disabled]
AI Clock Skew for Chennel A [Auto]
Current Clock Skew Advance300ps
AI Clock Skew for Channel B [Auto]
Current Clock Skew Advance300ps
AI Net 2
Marvell Post LAN cable [Disabled]
CPU Configuration
GART Error Reporting [Disabled]
Microcode Updation [Disabled]
Secure Virtual Machine Mode [Enabled]
AMD Cool 'n' Quiet Function [Disabled]
ACPI SRAT Table [Enabled]
AMD Live! [Disabled]
Chipset
PCI Express Configuration
GFX Dual Slot Configuration [Disabled]
Peer-to-Peer among GFX/GFX2 [Disabled]
GPP Slots Power Limit, W [25]
Port #02
Gen2 High Speed Mode [Software Switch]
Link ASPM [L0s & L1]
Link Width [x8]
Slot Power Limit, W [225]
Port#04 through #10
Gen2 High Speed Mode [Disabled]
Link ASPM [Disabled]
Port#11 Features Bottom blue slot
Gen2 High Speed Mode [Disable]
Link ASPM [Disable]
Link Width [Disable]
Slot Power Limit, W [75]
NB-SB Port Features
NB-SB Link ASPM [L1]
NP NB-SB VC1 Traffic Support [Enabled]
Hyper Transport Configuration
Isochronous Flow-Control Mode [Enabled]
HT Link Tristate [CAD/CTL/CLK]
UnitID Clumping [UnitID 2/3&B/C]
2xLCLK Mode [Disabled]
Onboard Devices Configuration
Onboard Floppy Controller [Disabled]
Floppy Drive Swap [Disabled]
Serial Port1 Address [Disabled]
Serial Port1 Mode [Normal]
HD Audio Azalia Device [Disabled]
Front Panel Support Type [HD Audio]
1394 [Disabled]
WiFi [Disabled]
Onboard LAN [Enable]
Onboard LAN Boot ROM [Disabled]
Marvell 6111 SATA Controller [Enable]
Marvell 6121 SATA Controller [Enable]
Marvell Option ROM [Disabled]
Primary Display Adapter [PCI-E]
PCI PnP
All settings left at default
POWER
Suspend Mode [S1 only]
Report Video on S3 Resume [No]
ACPI 2.0 Support [Enabled]
ACPI APIC Support [Enabled]
APM Configuration
all settings left at default
Harware Monitor
CPU Fan Warning Speed [Disabled]
Smart Q-Fan Function [Enabled]
Samrt Q-Fan Profile [Optimal]
BOOT
Quick Boot [Disabled]
Chassis Intrusion [Enabled]
Lite kommentar:
Varför krashar systemet? Beror det på antalet Volt jag anger till olika moderkort/processor delar?
vad ska jag ha för multipler för följande: "Processor-NB Frequency Multiplier"?
Hur ska jag ställa in inställningarna för att få stabilt och optimerat system (om möjligt lite OC också)? Fläktkyld system.
Mvh
Groom
