VARFÖR crashar dator J*veln "Hjälp" överklockning 4Ghz
Hejsan allihopa!
Jag har läst "FAQ" tråden för överklockning 1000 gånger minst, googlat på olika guider hur man överklockar en I7 930 till 4Ghz men jag får ta me fan inte min I7 i mitt P6X58D premium moderkort att funka som det ska, kan köra prime95 ca 5 timmar utan problem men när jag använder datorn samtidigt så crashar den precis som datorn kan köra om den får för lite volt.
Men rätta mig om jag har fel kan man köra Prime95, intel burn och memok under en natt så borde det inte vara några problem?
Senast den crasha körde jag på CPU volt 1,36250 och har provat höja nu till 1,37500 och se om det hjälper, men ser ni några saker som jag behöver direkt att ändra på så snälla skriv en liten kommentar.
Mina komponenter kan ni se i sign.
Temperaturerna i Load är runt 77 grader.
Ai Overclock Tuner.....................[Manual]
CPU Ratio Setting......................[21.0]
Intel (R) SpeedStep (TM) Tech...........[Disabled]
Xtreme Phase Full Power Mode...........[Enabled]
BCLK Frequency.........................[200]
PCIE Frequency.........................[100]
DRAM Frequency.........................[DDR3 - 1603 MHz]
UCLK Frequency.........................[AUTO]
QPI Link Data Rate.....................[AUTO]
CPU Voltage Control....................[MANUAL]
CPU Voltage............................[1.36250]
CPU PLL Voltage........................[1.82]
QPI/DRAM Core Voltage..................[1.26875]
IOH Voltage............................[1.14]
IOH PCIE Voltage.......................[1.50]
ICH Voltage............................[1.20]
ICH PCIE Voltage.......................[1.50]
DRAM Bus Voltage.......................[1.64]
DRAM DATA REF Voltage on CHA...........[Auto]
DRAM CTRL REF Voltage on CHA...........[Auto]
DRAM DATA REF Voltage on CHB...........[Auto]
DRAM CTRL REF Voltage on CHB...........[Auto]
DRAM DATA REF Voltage on CHC...........[Auto]
DRAM CTRL REF Voltage on CHC...........[Auto]
Load-Line Calibration..................[AUTO]
CPU Differential Amplitude.............[800mV]
CPU Clock Skew.........................[Delay 300ps]
CPU Spread Spectrum....................[Disabled]
IOH Clock Skew.........................[AUTO]
PCIE Spread Spectrum...................[Disabled]
C1E Support............................[Disabled]
Hardware Prefetcher....................[Enabled]
Adjacent Cache Line Prefetch...........[Enabled]
Intel(r) Virtualization Tech...........[Disabled]
CPU TM Function........................[Disabled]
Execute Disable Bit....................[Enabled]
Intel(r) HT Technology.................[Enabled]
Active Processor Cores.................[All]
A20M...................................[Disabled]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Intel(r) C-STATE Tech..................[Disabled]
1st Information: 8-8-8-24-7-98-15-9-28-0
DRAM CAS# Latency......................[8 DRAM Clock]
DRAM RAS# to CAS# Delay................[8 DRAM Clock]
DRAM RAS# PRE Time.....................[8 DRAM Clock]
DRAM RAS# ACT Time.....................[24 DRAM Clock]
DRAM RAS# to RAS# Delay................[Auto]
DRAM REF Cycle Time....................[Auto]
DRAM WRITE Recovery Time...............[Auto]
DRAM READ to PRE Time..................[Auto]
DRAM FOUR ACT WIN Time.................[Auto]
DRAM Back-To-Back CAS# Delay...........[Auto]
2nd Information: 2N-59-60-62
DRAM Timing Mode.......................[2N]
DRAM Round Trip Latency on CHA.........[Auto]
DRAM Round Trip Latency on CHB.........[Auto]
DRAM Round Trip Latency on CHC.........[Auto]
3rd Information: 7-7-19-9-9-9-7-6-4-7-7-4
DRAM WRITE To READ Delay (DD)..........[Auto]
DRAM WRITE To READ Delay (DR)..........[Auto]
DRAM WRITE To READ Delay (SR)..........[Auto]
DRAM READ To WRITE Delay (DD)..........[Auto]
DRAM READ To WRITE Delay (DR)..........[Auto]
DRAM READ To WRITE Delay (SR)..........[Auto]
DRAM READ To READ Delay (DD)...........[Auto]
DRAM READ To READ Delay (DR)...........[Auto]
DRAM READ To READ Delay (SR)...........[Auto]
DRAM WRITE to WRITE Delay (DD).........[Auto]
DRAM WRITE to WRITE Delay (DR).........[Auto]
DRAM WRITE to WRITE Delay (SR).........[Auto]
