Forum Ljud, bild och kommunikation Skärmar och TV-apparater Tråd Inlägg

Samlingstråd - fästen till TV (diskussionstråd)

1 2 3 4 5 6 7
Skriv svar
Permalänk
Medlem
●
Skrivet av Succinylkolin:

If I recall correctly, the minimum distance between two mollys in gypsum should be 20 cm. So you will have to do a bit of measuring. Personally I would have gone for 4 toggle bolts in the blue circles and then 2 mollys in the top green circles plus 1 molly in the bottom red circle.

Gå till inlägget

En gipsvägg kan såklart bara hålla så mycket per yta men det lär vara oberoende av fästanordningstyp. Sen är ju väggankare allmänt lite klurigt, man vill veta så att de vecklar ut sig korrekt i väggen, att det inte går på VP rör, flexslang eller regel som gör att de inte vecklas ut helt. Sen gäller det som sagt att väggen är hel och fin vilket inte alltid är fallet när det kommer till enkel gips. Handlar det om lägenhet så måste man alltid återställa väggarna men oftast blir det bara lite spackel och hur hållbart blir det då om det redan suttit 4-5 apparater på den väggen med ankare? Personligen hade jag inte hängt en dyr TV på enkelgips utan att testa motsvarande vikt över natten men det finns såklart drulleförsäkring Vanligtvis brukar jag vilja sätta iallafall par skruvar i en regel, lite hjälper det om väggen är dålig.

Visa signatur

CPU : AMD Ryzen 5 5600X Moderkort : ASUS ROG Strix B550-F GAMING Grafikkort :EVGA GeForce GTX 1080 Ti FTW3 iCX Gaming HDMI 3xDP 11GBMinne : Corsair 16GB Chassi :Fractal Design Define 7 Compact Nätdel : Corsair RM750x Skärm #1 : Asus VG349Q Ultrawide Skärm #2 : Acer X34 Ultrawide

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av Jimmy:

En gipsvägg kan såklart bara hålla så mycket per yta men det lär vara oberoende av fästanordningstyp. Sen är ju väggankare allmänt lite klurigt, man vill veta så att de vecklar ut sig korrekt i väggen, att det inte går på VP rör, flexslang eller regel som gör att de inte vecklas ut helt. Sen gäller det som sagt att väggen är hel och fin vilket inte alltid är fallet när det kommer till enkel gips. Handlar det om lägenhet så måste man alltid återställa väggarna men oftast blir det bara lite spackel och hur hållbart blir det då om det redan suttit 4-5 apparater på den väggen med ankare? Personligen hade jag inte hängt en dyr TV på enkelgips utan att testa motsvarande vikt över natten men det finns såklart drulleförsäkring Vanligtvis brukar jag vilja sätta iallafall par skruvar i en regel, lite hjälper det om väggen är dålig.

Gå till inlägget

Nej precis, jag skulle inte heller montera i gipsvägg utan att träffa ett par reglar. I det aktuella fallet 4 skruv i metallregel, och 3 molly i gips. Jag har bara monterat i träregel tidigare, men tänker att överstående bör hålla?

Redigera
Citera flera Citera
Permalänk
Medlem
●
Skrivet av last_grimm:

Hej, which option do you recommend ?

Blue Circle - Metal Studs location
Green & Red Circle - Single layer gypsum wall

Option 1 - 4 toggle bolts in Blue circles & 6 mollys in Red & Green circle

Option 2 - 4 toggle bolts in Blue circles & 2 mollys in Red circle

Option 3 - 4 toggle bolts in Blue circles & 4 mollys in Green circle

<Uppladdad bildlänk>

Gå till inlägget

Vet inte hur det är att sätta molly i metallreglar, gäller ju att alla benen vecklar ut sig korrekt, annars verkar T-ankare(ex Hilti gipsexpanders HTB-2) vara bra grejer för detta. Viktigt är såklart att hitta rätt i de U-formade plåtreglarna men de verkar du redan ha bra koll på. Man kan sätta T-ankare även i gipsen, det blir en smaksak och såklart lite frågan om hur många KG som behövs. Även molly pluggar har olika kapacitet beroende på storlek.

Så titta på hur mycket TVn väger inkl fäste, lägg på lite extra om någon skulle luta sig på TVn, lägg på en hel del extra om TVn ska fällas ut från väggen. Titta sedan på vilken kombination av gips expanderas som ger rimlig överkapacitet. Fäster T-ankare perfekt i plåtregeln kanske det i praktiken hade räckt med dessa 4 men här vill man inte chansa.

Är man nojig hänger man som sagt något annat tåligt i TV hållaren över natten med samma vikt men det bör inte vara några problem här.

Visa signatur

CPU : AMD Ryzen 5 5600X Moderkort : ASUS ROG Strix B550-F GAMING Grafikkort :EVGA GeForce GTX 1080 Ti FTW3 iCX Gaming HDMI 3xDP 11GBMinne : Corsair 16GB Chassi :Fractal Design Define 7 Compact Nätdel : Corsair RM750x Skärm #1 : Asus VG349Q Ultrawide Skärm #2 : Acer X34 Ultrawide

Redigera
Citera flera Citera
Permalänk
Medlem
●
Skrivet av Succinylkolin:

If I recall correctly, the minimum distance between two mollys in gypsum should be 20 cm. So you will have to do a bit of measuring. Personally I would have gone for 4 toggle bolts in the blue circles and then 2 mollys in the top green circles plus 1 molly in the bottom red circle.

Gå till inlägget
Skrivet av Jimmy:

En gipsvägg kan såklart bara hålla så mycket per yta men det lär vara oberoende av fästanordningstyp. Sen är ju väggankare allmänt lite klurigt, man vill veta så att de vecklar ut sig korrekt i väggen, att det inte går på VP rör, flexslang eller regel som gör att de inte vecklas ut helt. Sen gäller det som sagt att väggen är hel och fin vilket inte alltid är fallet när det kommer till enkel gips. Handlar det om lägenhet så måste man alltid återställa väggarna men oftast blir det bara lite spackel och hur hållbart blir det då om det redan suttit 4-5 apparater på den väggen med ankare? Personligen hade jag inte hängt en dyr TV på enkelgips utan att testa motsvarande vikt över natten men det finns såklart drulleförsäkring Vanligtvis brukar jag vilja sätta iallafall par skruvar i en regel, lite hjälper det om väggen är dålig.

Gå till inlägget
Skrivet av Succinylkolin:

Nej precis, jag skulle inte heller montera i gipsvägg utan att träffa ett par reglar. I det aktuella fallet 4 skruv i metallregel, och 3 molly i gips. Jag har bara monterat i träregel tidigare, men tänker att överstående bör hålla?

Gå till inlägget
Skrivet av Jimmy:

Vet inte hur det är att sätta molly i metallreglar, gäller ju att alla benen vecklar ut sig korrekt, annars verkar T-ankare(ex Hilti gipsexpanders HTB-2) vara bra grejer för detta. Viktigt är såklart att hitta rätt i de U-formade plåtreglarna men de verkar du redan ha bra koll på. Man kan sätta T-ankare även i gipsen, det blir en smaksak och såklart lite frågan om hur många KG som behövs. Även molly pluggar har olika kapacitet beroende på storlek.

Så titta på hur mycket TVn väger inkl fäste, lägg på lite extra om någon skulle luta sig på TVn, lägg på en hel del extra om TVn ska fällas ut från väggen. Titta sedan på vilken kombination av gips expanderas som ger rimlig överkapacitet. Fäster T-ankare perfekt i plåtregeln kanske det i praktiken hade räckt med dessa 4 men här vill man inte chansa.

Är man nojig hänger man som sagt något annat tåligt i TV hållaren över natten med samma vikt men det bör inte vara några problem här.

Gå till inlägget

First of all Tack for your kind suggestions !

After reading & considering your comments, here's what my plan is -

I plan to use 4 T-anchors in the metal studs. Ideally these should just suffice, however for extra protection I will use 3 mollys (2 on the top part & 1 in bottom of mount) in the drywall as I do plan to pull out the TV and use it.

I will put a tiny camera inside the wall to make sure no pipes etc. are getting hit.

I will put double the TV weight & leave it overnight.

For extra protection I have the drull insurance & also the premium insurance from LG.

The T-anchor is this one -

https://www.amazon.se/Toggler-25029-SnapToggler-Anchor-Silver...

Molly this one -

https://www.amazon.se/-/en/dp/B00MQRDZMU/ref=d_pd_sbs_sccl_2_...

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

First of all Tack for your kind suggestions !

After reading & considering your comments, here's what my plan is -

I plan to use 4 T-anchors in the metal studs. Ideally these should just suffice, however for extra protection I will use 3 mollys (2 on the top part & 1 in bottom of mount) in the drywall as I do plan to pull out the TV and use it.

I will put a tiny camera inside the wall to make sure no pipes etc. are getting hit.

I will put double the TV weight & leave it overnight.

For extra protection I have the drull insurance & also the premium insurance from LG.

The T-anchor is this one -

https://www.amazon.se/Toggler-25029-SnapToggler-Anchor-Silver...

Molly this one -

https://www.amazon.se/-/en/dp/B00MQRDZMU/ref=d_pd_sbs_sccl_2_...

Gå till inlägget

Good luck and return with pictures! What kind of camera are you using?

Redigera
Citera flera Citera
Permalänk
Medlem
●
Skrivet av Succinylkolin:

Good luck and return with pictures! What kind of camera are you using?

Gå till inlägget

Thanks !

This one -

https://www.amazon.se/dp/B073S65LRP/ref=sr_1_24_sspa?keywords...

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

First of all Tack for your kind suggestions !

After reading & considering your comments, here's what my plan is -

I plan to use 4 T-anchors in the metal studs. Ideally these should just suffice, however for extra protection I will use 3 mollys (2 on the top part & 1 in bottom of mount) in the drywall as I do plan to pull out the TV and use it.

I will put a tiny camera inside the wall to make sure no pipes etc. are getting hit.

I will put double the TV weight & leave it overnight.

For extra protection I have the drull insurance & also the premium insurance from LG.

The T-anchor is this one -

https://www.amazon.se/Toggler-25029-SnapToggler-Anchor-Silver...

Molly this one -

https://www.amazon.se/-/en/dp/B00MQRDZMU/ref=d_pd_sbs_sccl_2_...

Gå till inlägget

Overloading is a good plan! That makes it way more safe. Keep in mind to load it a bit away from the wall to simulate where the load from a TV would be

Drill the first hole near center (one of the molly holes) and then use camera before drilling more holes (just to make sure). A stud/electrical-finder can be useful before this hole is drilled just to be sure. Also it takes a while to make a hole in a metal pipe, just stop drilling and look in the hole if there is any weird resistance

Doing it the way you are suggesting will be way more than minimum requirements, i dont think you will have any issues

Even skipping the studs completely would probably be sufficient (using mollys instead) or using just the stud mounts. Better to be safe than sorry though

Redigera
Citera flera Citera
Permalänk
Medlem
●
Skrivet av medbor:

Overloading is a good plan! That makes it way more safe. Keep in mind to load it a bit away from the wall to simulate where the load from a TV would be

Drill the first hole near center (one of the molly holes) and then use camera before drilling more holes (just to make sure). A stud/electrical-finder can be useful before this hole is drilled just to be sure. Also it takes a while to make a hole in a metal pipe, just stop drilling and look in the hole if there is any weird resistance

Doing it the way you are suggesting will be way more than minimum requirements, i dont think you will have any issues

Even skipping the studs completely would probably be sufficient (using mollys instead) or using just the stud mounts. Better to be safe than sorry though

Gå till inlägget

thanks for the feedback.

Yes, I do plan on using the stud finder also to be sure before drilling holes. And it's always good to be safe than sorry. Good thing is C2 77" is just 20 KGs, so not like a typical LED or C1 weight which are really heavy.

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

thanks for the feedback.

Yes, I do plan on using the stud finder also to be sure before drilling holes. And it's always good to be safe than sorry. Good thing is C2 77" is just 20 KGs, so not like a typical LED or C1 weight which are really heavy.

Gå till inlägget

I would never dream of wall mounting my 77B1, sure it can be done, but i just would rather not get into that

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

Hey can you share finished pictures of your setup ? Curious to see how it looks from the side & front.

Gå till inlägget

Haha the setup isn't done yet. The hard part is getting the finishing touches done, such as spotlights and cover panels to get everything seamless. This is how it looks like right now.

Some pictures of how it looks like behind. Went for an articulating mount mostly to make it easier to access the ports on the back:

And the front:

It may be quite far away from the wall compared to more conventional mounts and mounting methods, but you really don't notice it whatsoever when you're sitting in front of it all.

Skrivet av medbor:

I would never dream of wall mounting my 77B1, sure it can be done, but i just would rather not get into that

Gå till inlägget

Svårt är det inte, bara om man vill ha ett ledat väggfäste

Visa signatur

Gamingrig | Intel Core i7-6700K @ 4.2 GHz | Nvidia GeForce GTX 980 Ti | ASUS ROG Maximus VIII Formula | 16GB 2133MHz HyperX DDR4 | SSD: Samsung 850 Pro 512GB + Intel 535 480GB + Samsung 840 Pro 256GB | HDD: 2x WD Black 2TB + 2x WD Green 4TB | Creative Sound Blaster ZxR+Sennheiser HD650 | Corsair RM1000 | Corsair H100i V2 | Phanteks P400S Tempered glass | Asus ROG Swift 1440p 165Hz + Asus 1440p PLS | Retina Macbook Pro | i7-3820QM | 8GB RAM | MS Surface Pro 3&4 | Intel i5 | 8GB RAM | 256GB SSD |

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av XFTality:

Haha the setup isn't done yet. The hard part is getting the finishing touches done, such as spotlights and cover panels to get everything seamless. This is how it looks like right now.

Some pictures of how it looks like behind. Went for an articulating mount mostly to make it easier to access the ports on the back:
<Uppladdad bildlänk>
<Uppladdad bildlänk>

And the front:
<Uppladdad bildlänk>
<Uppladdad bildlänk>

It may be quite far away from the wall compared to more conventional mounts and mounting methods, but you really don't notice it whatsoever when you're sitting in front of it all.

Svårt är det inte, bara om man vill ha ett ledat väggfäste

Gå till inlägget

Nice job, that looks great!

My main issue with wall mounting is that it is not facing a wall, but rather the back of a cabinet section. I would have to change the entire room to even have the possibility to do it

Redigera
Citera flera Citera
Permalänk
Medlem
●
Skrivet av medbor:

I would never dream of wall mounting my 77B1, sure it can be done, but i just would rather not get into that

Gå till inlägget

For me it's a necessity now, given how delicate the OLED is & the big size, I worry someone will accidently hit it when I have lot of people over for a get together or something. The walking passage is right in front of the TV cabinet.

Skrivet av XFTality:

Haha the setup isn't done yet. The hard part is getting the finishing touches done, such as spotlights and cover panels to get everything seamless. This is how it looks like right now.

Some pictures of how it looks like behind. Went for an articulating mount mostly to make it easier to access the ports on the back:
<Uppladdad bildlänk>
<Uppladdad bildlänk>

And the front:
<Uppladdad bildlänk>
<Uppladdad bildlänk>

It may be quite far away from the wall compared to more conventional mounts and mounting methods, but you really don't notice it whatsoever when you're sitting in front of it all.

Svårt är det inte, bara om man vill ha ett ledat väggfäste

Gå till inlägget

Thank you for sharing the pictures. Very nicely done. While I'm contemplating to use the wooden plank, but given that my TV sits in the living room with the back exposed when you walk towards the living room, it might look messy from the side.

Hence I might go with 4 T anchors in metal studs & 3 mollys as suggested here. Even with full pull out it should be enough I believe.

Redigera
Citera flera Citera
Permalänk
Medlem
●

2 questions -

A) Probably a controversial question, but how high do you mount your TV ?

B) How do you run the wires in the drywall ? I bought this to make a cut (near the TV mount) and then one more cut towards the bottom.

https://www.amazon.de/-/en/gp/product/B07CSN9HJ9/ref=ppx_yo_d...

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

2 questions -

A) Probably a controversial question, but how high do you mount your TV ?

B) How do you run the wires in the drywall ? I bought this to make a cut (near the TV mount) and then one more cut towards the bottom.

https://www.amazon.de/-/en/gp/product/B07CSN9HJ9/ref=ppx_yo_d...

Gå till inlägget

Center of TV at eye height or lower

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

2 questions -

A) Probably a controversial question, but how high do you mount your TV ?

B) How do you run the wires in the drywall ? I bought this to make a cut (near the TV mount) and then one more cut towards the bottom.

https://www.amazon.de/-/en/gp/product/B07CSN9HJ9/ref=ppx_yo_d...

Gå till inlägget

We tried several heights, and ended up with my 77B1 at about 65cm from the floor when viewed from about 2.5m (eye to panel distance).

The bottom of the panel is roughly in line with the seat height of the sofas

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

B) How do you run the wires in the drywall ? I bought this to make a cut (near the TV mount) and then one more cut towards the bottom.

https://www.amazon.de/-/en/gp/product/B07CSN9HJ9/ref=ppx_yo_d...

Gå till inlägget

I don't run any cables through the wall. It sure looks nice but I'm not sure you are "allowed" to run power cables through the wall as a non-electrician. If something were to happen I think there could be problems with the insurance company.

Redigera
Citera flera Citera
Permalänk
Medlem
●

Alright ! So ran into a major challenge today. Turns out the distance between the 2 studs is 47 CM ! Not the standard 40 CM. Because of this I'm 5 CM short on the length & can't use both the studs.

So I either use only 1 stud OR redo the entire process, buy a new mount & attempt the installation again ! OR put a plywood in between & mount on it as XFTality did.

The journey continues........so does the messy house !

Redigera
Citera flera Citera
Permalänk
Medlem
●
Skrivet av XFTality:

Haha the setup isn't done yet. The hard part is getting the finishing touches done, such as spotlights and cover panels to get everything seamless. This is how it looks like right now.

Some pictures of how it looks like behind. Went for an articulating mount mostly to make it easier to access the ports on the back:
<Uppladdad bildlänk>
<Uppladdad bildlänk>

And the front:
<Uppladdad bildlänk>
<Uppladdad bildlänk>

It may be quite far away from the wall compared to more conventional mounts and mounting methods, but you really don't notice it whatsoever when you're sitting in front of it all.

Svårt är det inte, bara om man vill ha ett ledat väggfäste

Gå till inlägget

Hey, I might be going down the same route. Few questions I had on your setup, it'll be great if you can answer them

A. What's the thickness & dimension of the plywood ? I have one from Ikea which is 58 x 58 CM and 2 CM thick.

B. You used 10 Molly in drywall & 8 screws in metal stud in total to support the plywood. How about the TV mount & the plywood ? How many & what type of screw did you use to connect the TV mount with plywood ?

C. While connecting TV mount to plywood, did you drill all the way to the drywall or only till the depth of the plywood ?

Many thanks in advance !

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

Hey, I might be going down the same route. Few questions I had on your setup, it'll be great if you can answer them

A. What's the thickness & dimension of the plywood ? I have one from Ikea which is 58 x 58 CM and 2 CM thick.

B. You used 10 Molly in drywall & 8 screws in metal stud in total to support the plywood. How about the TV mount & the plywood ? How many & what type of screw did you use to connect the TV mount with plywood ?

C. While connecting TV mount to plywood, did you drill all the way to the drywall or only till the depth of the plywood ?

Many thanks in advance !

Gå till inlägget

I would say:

A: That is plenty
B1: just 6 (or 8 if you want to go overkill) screws total into the studs and you are fine.
B2:Normal wood screws are fine when attaching the stand to the plywood. For example. As long as the screw goes all the way through the plywood and then a little further (for example, 19 mm plywood I would recommend 25-30 mm screws). Then ofcourse add any extra length that is needed due to the thickness of the TV mount. My guess is you could bye 40 mm screws and you are good to go. You should use a:
https://www.biltema.se/en-se/construction/fixing-elements/woo...
or
https://www.biltema.se/en-se/construction/fixing-elements/woo...
depending on how thick your mount is. The important part is that the "screw" part is penetrating the plywood in a good way.
C: No need to pre-drill into the plywood. Just screw it in as it is Unless you are planning on using a VERY thick screw, which should definitely not be needed.

Visa signatur

5700x3D | RTX 2060 Super | 2 TB M.2 | 32 GB RAM | Gigabyte DS3H| 750 WATT

Redigera
Citera flera Citera
Permalänk
Medlem
●
Skrivet av FX9:

I would say:

A: That is plenty
B1: just 6 (or 8 if you want to go overkill) screws total into the studs and you are fine.
B2:Normal wood screws are fine when attaching the stand to the plywood. For example. As long as the screw goes all the way through the plywood and then a little further (for example, 19 mm plywood I would recommend 25-30 mm screws). Then ofcourse add any extra length that is needed due to the thickness of the TV mount. My guess is you could bye 40 mm screws and you are good to go. You should use a:
https://www.biltema.se/en-se/construction/fixing-elements/woo...
or
https://www.biltema.se/en-se/construction/fixing-elements/woo...
depending on how thick your mount is. The important part is that the "screw" part is penetrating the plywood in a good way.
C: No need to pre-drill into the plywood. Just screw it in as it is Unless you are planning on using a VERY thick screw, which should definitely not be needed.

Gå till inlägget

Hej thanks for the super quick reply Few follow up questions.

A: That is plenty - Done, I'll use the Ikea one. This is the one - https://www.ikea.com/se/sv/p/utrusta-hyllplan-vit-50205612/

B1: just 6 (or 8 if you want to go overkill) screws total into the studs and you are fine. - I plan on using the Toogle bolts for the metal stud part.

B2:Normal wood screws are fine when attaching the stand to the plywood. For example. As long as the screw goes all the way through the plywood and then a little further (for example, 19 mm plywood I would recommend 25-30 mm screws). Then ofcourse add any extra length that is needed due to the thickness of the TV mount. My guess is you could bye 40 mm screws and you are good to go. You should use a:
https://www.biltema.se/en-se/construction/fixing-elements/woo...
or
https://www.biltema.se/en-se/construction/fixing-elements/woo...
depending on how thick your mount is. The important part is that the "screw" part is penetrating the plywood in a good way.

Should I use anchors for extra protection when screwing the mount to plywood ? Something like this - https://www.amazon.se/-/en/dp/B01LZL2JI1/ref=pd_day0fbt_img_s...

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

Hej thanks for the super quick reply Few follow up questions.

A: That is plenty - Done, I'll use the Ikea one. This is the one - https://www.ikea.com/se/sv/p/utrusta-hyllplan-vit-50205612/

B1: just 6 (or 8 if you want to go overkill) screws total into the studs and you are fine. - I plan on using the Toogle bolts for the metal stud part.

B2:Normal wood screws are fine when attaching the stand to the plywood. For example. As long as the screw goes all the way through the plywood and then a little further (for example, 19 mm plywood I would recommend 25-30 mm screws). Then ofcourse add any extra length that is needed due to the thickness of the TV mount. My guess is you could bye 40 mm screws and you are good to go. You should use a:
https://www.biltema.se/en-se/construction/fixing-elements/woo...
or
https://www.biltema.se/en-se/construction/fixing-elements/woo...
depending on how thick your mount is. The important part is that the "screw" part is penetrating the plywood in a good way.

Should I use anchors for extra protection when screwing the mount to plywood ? Something like this - https://www.amazon.se/-/en/dp/B01LZL2JI1/ref=pd_day0fbt_img_s...

Gå till inlägget

Those plastic anchors are for light duty mounting in bad materials (concrete, gypsum, …). They expand slightly and grip by friction. I would never use those in wood, a normal wood screw holds much more securely

One option would be to mount the tv with a stud near center of the mount. It will hold just fine. Just a matter of if the tv can move 20cm in one direction

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av medbor:

Those plastic anchors are for light duty mounting in bad materials (concrete, gypsum, …). They expand slightly and grip by friction. I would never use those in wood, a normal wood screw holds much more securely

One option would be to mount the tv with a stud near center of the mount. It will hold just fine. Just a matter of if the tv can move 20cm in one direction

Gå till inlägget

Totally agree, just stick with normal wood screws, they will be plenty!

Visa signatur

5700x3D | RTX 2060 Super | 2 TB M.2 | 32 GB RAM | Gigabyte DS3H| 750 WATT

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

Hej thanks for the super quick reply Few follow up questions.

A: That is plenty - Done, I'll use the Ikea one. This is the one - https://www.ikea.com/se/sv/p/utrusta-hyllplan-vit-50205612/

Gå till inlägget

Don't use the Ikea one. That is not a good material for this I would say. It is not plywood and will not hold too well. It is simply not solid enough

This is better:
https://www.biltema.se/en-se/construction/storage-shelves/she...

The Ikea one will hold your weight fine, but the screws will not be as tightly secured and could come out. My suggestion is more solid wood and will carry pretty much anything

Pick the one named: SHELF 1000X400X18MM
18 mm thick, and you should not need more then 400 mm high (atleast I don't think so, but it depends on your TV stand)

You will have to cut it to around 50 CM (since your studs are at around 47 cm apart, but you can do that by hand with a saw.

And just add some paint to it when done, and it will not look that bad either

Visa signatur

5700x3D | RTX 2060 Super | 2 TB M.2 | 32 GB RAM | Gigabyte DS3H| 750 WATT

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

Hej thanks for the super quick reply Few follow up questions.

A: That is plenty - Done, I'll use the Ikea one. This is the one - https://www.ikea.com/se/sv/p/utrusta-hyllplan-vit-50205612/

B1: just 6 (or 8 if you want to go overkill) screws total into the studs and you are fine. - I plan on using the Toogle bolts for the metal stud part.

B2:Normal wood screws are fine when attaching the stand to the plywood. For example. As long as the screw goes all the way through the plywood and then a little further (for example, 19 mm plywood I would recommend 25-30 mm screws). Then ofcourse add any extra length that is needed due to the thickness of the TV mount. My guess is you could bye 40 mm screws and you are good to go. You should use a:
https://www.biltema.se/en-se/construction/fixing-elements/woo...
or
https://www.biltema.se/en-se/construction/fixing-elements/woo...
depending on how thick your mount is. The important part is that the "screw" part is penetrating the plywood in a good way.

Should I use anchors for extra protection when screwing the mount to plywood ? Something like this - https://www.amazon.se/-/en/dp/B01LZL2JI1/ref=pd_day0fbt_img_s...

Gå till inlägget

Video has a lot of good tips

https://www.google.com/search?q=attach+to+metal+studs&oq=atta...

https://www.google.com/search?q=attach+to+metal+studs&oq=atta...

Will give you a good idea of how this will work

Senast redigerat
Visa signatur

5700x3D | RTX 2060 Super | 2 TB M.2 | 32 GB RAM | Gigabyte DS3H| 750 WATT

Redigera
Citera flera Citera
Permalänk
Medlem
●
Skrivet av medbor:

Those plastic anchors are for light duty mounting in bad materials (concrete, gypsum, …). They expand slightly and grip by friction. I would never use those in wood, a normal wood screw holds much more securely

One option would be to mount the tv with a stud near center of the mount. It will hold just fine. Just a matter of if the tv can move 20cm in one direction

Gå till inlägget

Well that's a bloody good idea ! I just checked, I can actually move the center to right & use ONE metal stud with the center of the mount.

I can use the 3 holes (which are there in the center of the mount & 7 cm apart) with the metal stud, put toggle bolt in all 3. Use 8 mollys in the remaining holes with the single layer gypsum wall.

This can be an alternate to the plywood idea which I'm considering.

Thank you!

Redigera
Citera flera Citera
Permalänk
Medlem
●
Skrivet av FX9:

Don't use the Ikea one. That is not a good material for this I would say. It is not plywood and will not hold too well. It is simply not solid enough

This is better:
https://www.biltema.se/en-se/construction/storage-shelves/she...

The Ikea one will hold your weight fine, but the screws will not be as tightly secured and could come out. My suggestion is more solid wood and will carry pretty much anything

Pick the one named: SHELF 1000X400X18MM
18 mm thick, and you should not need more then 400 mm high (atleast I don't think so, but it depends on your TV stand)

You will have to cut it to around 50 CM (since your studs are at around 47 cm apart, but you can do that by hand with a saw.

And just add some paint to it when done, and it will not look that bad either

Gå till inlägget

Hey a big thank you again !

Good that I did not start installing the Ikea one That video was very helpful.

I'm also contemplating to go with medbor's suggestion of using one metal stud as the center of TV. For sure it will be less effective as the plywood method, but should be enough for 20KG TV I'm hoping. If not, then a trip to Bauhaus or Biltema has to be done I guess.

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av last_grimm:

Well that's a bloody good idea ! I just checked, I can actually move the center to right & use ONE metal stud with the center of the mount.

I can use the 3 holes (which are there in the center of the mount & 7 cm apart) with the metal stud, put toggle bolt in all 3. Use 8 mollys in the remaining holes with the single layer gypsum wall.

This can be an alternate to the plywood idea which I'm considering.

Thank you!

Gå till inlägget

The ikea board is ’chipboard’ or particleboard not plywood, not at all as durable or strong, just to make sure you got that. For this application it would probably have been fine, but it is not the same

Also ikea might have hollow centers if you are unlucky with specific parts:

But on the other topic: yes a single stud will easily hold that TV in place, even only the mollys in drywall should suffice on their own really (assuming a pretty slim mounting without a long moment arm, wiki)

Senast redigerat
Redigera
Citera flera Citera
Permalänk
Medlem
●

Någon som kan tipsa om ett bra/säkert väggfäste till en 77” TV som enligt specifikation väger 26,7kg (en Lg c1)? Det ska vara fast, dvs inte några rörliga delar för att tilta/luta eller flytta tvn. Och det verkar vara vesa 400x400.

Redigera
Citera flera Citera
Permalänk
Medlem ★
●
Skrivet av naaw:

Någon som kan tipsa om ett bra/säkert väggfäste till en 77” TV som enligt specifikation väger 26,7kg (en Lg c1)? Det ska vara fast, dvs inte några rörliga delar för att tilta/luta eller flytta tvn. Och det verkar vara vesa 400x400.

Gå till inlägget

Jag har min 75" TV väggmonterad med detta: https://www.komplett.se/product/1122132/tv-ljud-bild/tv-tillb...

Vad är det för vägg du ska montera på?

Redigera
Citera flera Citera
Permalänk
Medlem
●
Skrivet av Succinylkolin:

Jag har min 75" TV väggmonterad med detta: https://www.komplett.se/product/1122132/tv-ljud-bild/tv-tillb...

Vad är det för vägg du ska montera på?

Gå till inlägget

Yes, jag såg ditt inlägg på första sidan. Hade hoppats med lite fler förslag. Men tack i alla fall! Om ingen annan kommer med åsikter så kommer det sannolikt bli det.

Är du nöjd hitills? Känns stabilt och säkert? Din TV ligger inte på återvinningscentralen och väggen har inte ett stort hål?

Redigera
Citera flera Citera
1 2 3 4 5 6 7
Skriv svar
Senaste nyheterna
Hårdvara
Mjukvara
Övrigt
Nytt i forumet
Datorkomponenter
System
Ljud, bild och kommunikation
Spel och mjukvara