MetallicAcid's TJ07 (working title)

Update time!

[size="3"]Well hello there! I thought I would share a little how to of how I splice my cables together when creating custom cables. I did not think to do the sleeving side of things though as I did not have enough time to take photos... I have just the time when my daughter is napping during the days to get my work done

So here comes a little "How-to" my way

You will need one of these to begin with. You know what they say - "helping hands with a magnifying glass are better than a sandwich!"... No wait :S

Firstly I lay out my cable. I cut the "parent" cable to size, and recrimp as needed. I then map out the "fetus" cable to length and strip the ends 6mm. I then proceed to remove a 6mm chunk from the "parent" cable where I want the splice to occur.

I then take a knife and split the wires on the parent cable to make a hole. I then split the wire on the fetus cable to make a prong/fork.

I thread one side of the fetus fork through the hole.

I then twist both sides of the fetus fork in the same direction around the parent cable's loop, forming a strong bond.

I then "pre tin" the soldering iron with a little bit of tin so that the tip is wet, as I believe this transfers heat better when the tin is already forming onto the wires. I proceed to hold the soldering iron under the twisted wire, with the tin on top. I hold both onto the wires until the entire connection is hot enough, and the tin starts melting though the wires without being in direct contact with the soldering iron's tip. I find that this is best as there is minimal tin on the outside of the wire's as most of hit has melted THROUGH all of the wires, forming a super awesome bond. NOTE: Make sure that the two cables plastic wrap are not touching when doing this technique are not touching, otherwise they will melt together and have to be cut apart.

And then repeat.

As a small text guide on how I did the sleeving... (Bare with me here )
I sleeved the shortest cable first so that the sleevings length covered the solder. I then proceeded to sleeve the other 2 wires so that the sleeving meets the shorter wire I sleeved previously. I then put on a piece of heatshrink and warmed it enough so that the sleeving underneath melts and forms a bond to each other. IF the heatshrink melts a little, it's no biggie, just use another and warm it slightly to that it shrinks and covers the ugly.

I hope this helps you in your journey to sleeving, or creating custom cables. This is the result that I was able to achieve:

So thank you once again for reading, and hope to see you in the next update!
Best regards,
Justin "MetallicAcid" Ohlsen

Update time!

[size="3"]Gday guys and girls!

I would just like to take this time to announce Inet.se as a sponsor, as they have provided an NZXT 10 ports fan hub to the project. Thanks guys! So in normal order, I have unboxed this product for all to see. Please enjoy!

Best regards,
Justin "MetallicAcid" Ohlsen

Update time!

[size="3"]Hey everybody! Welcome again!

It has been a little while since the last update. I would like to say thank you to you who have patiently waited until the hardware started trickling in! I have a nice little update for you guys which includes a beastly motherboard, some overkill RAM, and EK waterblocks (non-sponsored). These parts were all bought second hand, hence why they are a little dusty! I thought that I would like to just let the pictures do the talking here...

So just a little text teaser as well, there is some more hardware coming in over the next few days, including fans, soundcard and SSDs. Thanks for reading, and see you in the next update!

With kind regards,
Justin "MetallicAcid" Ohlsen

Update time!

[size="3"]Hey hey!

A short update for you all I have got the case back from the powder coaters today. I am 90% happy with how it turned out, but there is a spot that looks like fingerprints.. You will see when you scroll through the pictures. I am going to give the shop a call tomorrow morning and see what they have to say about it. So without any further waiting, here come the photos!

Now that I have the case painted, I am pushing to get the CPU here ASAP so I can install the motherboard uniblock, drill the necessary holes and get the tubing routed.

I hope that you have enjoyed this update!

Kind regards,
Justin "MetallicAcid" Ohlsen

[size="3"]Hey everybody!

Since completing my last project, the Monolith FT03, I have gotten my arse into gear to finish this TJ07 before the end of this month. I will try and keep you guys up to date on what is going, and have at least one update a week.

In this update, I have gotten in almost all of the parts required to get this project finished. I am just waiting on the GPU blocks from coolerkit.se.

With this update I would also like to announce BlackNoise as a sponsor, who have given this project 6 of their Noiseblocker NB BlackSilent Pro 120mm PL-2 fans.
Here is what they look like

Once I checked out and installed those beauties, I had a look at the 4 AMD R9 290's which was sent to me for the project. Do not worry my friends, these will be water cooled, and these original coolers will be scrapped for the sake of humankind.

I got in a brand spanking new Intel Core i7 4930k as well. Let's check it out!

After I had finished drooling on the CPU, I went ahead and installed it on the motherboard, then swapped out the EK motherboard blocks for this beautiful uniblock. This will really tidy things up reducing the amount of fittings from 6 to just 2. I also decided to remove the RAM water cooling blocks as they are not needed, and create unnecessary mess/fittings/tube routing. Where is what it all looks like during and after installation.

Other things that I would like to mention is that I have bought a pipe bender, pipe cutter and chromed piping for this build. The tube bending will start this Saturday, and hopefully the GPU blocks have come in so I can get this sorted out.

Also, I will have to mod the Cold Zero motherboard extension plate as the holes for the GPUs no longer match up with the amount of GPUs that will be installed. I will be installing just 3 cards, as the Silverstone 1200w PSU will not handle the 4th card This also means that I have to cut an extra hole into the extension tray to accommodate this extra GPU.

I think that is about it for this update guys. I hope that I have not kept you waiting too long, but with tight budgeting and parts costing as much as they do, it was unavoidable. But this said, from now on it should be short and sweet!

Cheers!
Justin "MetallicAcid" Ohlsen