Inlägg

Hej !

Vad ska du använda den till ? Kvalitet, Utseend, Storlek på chassi osv........
Kan ju vara bra att vet när man ska välja komponenter

Som det verkar så ska det vara billigt och då tycker jag att du köpa det.

Men jag råder dig att vänta och spara ihop till ett bra chassi
för du kommer att bli besviken på det.

Personligen gillar jag Thermaltake
men det finns ju andra bra lådor, e ju lite av en smaksak

Ha d

Jag har ett striker extreme och använder dessa inställningar
verkar funka för mig iaf

lycka till

So then we are ready to test memory.
Tool we need for this is memtest86+
http://www.memtest.org/#downiso

Why is it important to use this tool??
If you gone RMA you chip,the shop will for sure use this tool.
It can make the hole RMA prosses harder if memory pass in shop.

There is a problem with memtest an 680i.
It will pass on to high volt to memory.
So a rule for 680i LOW VOLT TO MEMORY GIVE BETTER STABILITY.
To high volt can kill memory on 680i.
http://vip.asus.com/forum/view.aspx?id=20070421075356734&boar...

Testing is the same 2-4-8GB memory
I gone talk abought 4GB because many have problem with it.
Patch link for vista
http://vip.asus.com/forum/view.aspx?id=20070426212656702&boar...

First as always on 680i we gone set some correct parameters in bios.
Never test on default bios setting.

Bios must be 1002 or 1102 or newer.
Here is 4GB fix for most memory.
I did a test to be sure with 0302(here was max 667mhz 4GB)

Sli reay disable dont like it,and it has nothing to do with performence.

So i gone use my memory as an exp.
Crucial 6400 4GB 4.4.4.12 800mhz
So this is how my bios config will look
Nothing OC when we test.

.....TEMPLATE.......

AI Tuning: Manual
Nvidia GPU Ex: Disabled
LinkBoost: Disabled

FSB - Memory Clock Mode: Unlinked
x FSB - Memory Raio: 10 default
FSB (QDR), Mhz: 1066(means 266FSB)
Actual FSB (QDR),1066mzh
MEM (DDR), Mhz: 800 (means 400mhz speeds)
Actual MEM (DDR), Mhz: 800

Vcore Voltage: Around 1.25v
Memory Voltage: 2.0v----for stock 800mzh this should be enough---
1.2v HT Voltage: 1.35v
NB Core Voltage: 1.4v
SB Core Voltage: Auto
CPU VTT Voltage: 1.4v
DDRII Controller Ref Voltage: AUTO
DDRII Channel A Ref Voltage: AUTO
DDRII Channel B Ref Voltage: AUTO

tCL (CAS Latency 4
tRCD 4
tRP 4
tRAS 12
Command Per Clock (CMD): 2 clock (2T)

Advance Memory Settings
tRRD: AUTO
tRC: AUTO
tWR: AUTO
tWTR: AUTO
tREF: AUTO
Async Latency: AUTO

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
MCP PCIE Spread Spectrum: Disabled
SATA Spread Spectrum: Disabled
LDT Spread Spectrum: Disabled

CPU Internal Thermal Control: Disabled
Limit CPUID MaxVal: Disabled
Enhanced C1 (C1E): Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled
Enhanced Intel Speedstep Tech: Disabled
LDT Frequency: 5x

PCIEX16_1 Frequency (Mhz): 100
PCIEX16_2 Frequency (Mhz): 100
PCIEX16_3 Frequency (Mhz): 100
SPP<->MCP Ref Clock, Mhz: 200
-----------------------------------------------------------------------------

Then i will start with 2GB in blue slot.
Then boot memtest(i never boot windows before i have testet memory in memtest)
Bad memory can destroy files an windows.

Then just watch that no error come.
I would recomend 1 pass.
If you dont have time be sure it pass test 5(test 5 is the hardest and ofen here you get error)
If error try go a little higer than 2.0v

So it pass with 0 error in blue slot.
Then we put next match par in white slot
And we do the same.

If it work we now that all memory and all slot work.

Then we put in all memory.
And we start lower mzh,to make sure they work together(500mzh)
And boot metest 0 error on 500mzh
Then try at default speed 800mzh.
0 error then we have working 4GB MEMORY.

-------------------------TIMEINGS AND DIVIDERS---------------------------------
Here is a god guide explaining timeings for 680i
http://www.xtremesystems.org/forums/showthread.php?p=2125236#...

So dividers have done some explaining in picture.
I use unlink then board auto choose dividers
Close to what i explain in picture.

On this board there are dividers that are stronger than other.
This is important to know if you gone oc this board.

Here i gone use Kunnak testing as exp.
Qutoe:
500 FSB - 800 mhz ram = no boot.
500 FSB - 1000 mhz ram = works fine.
500 FSB - 1100 mhz ram = boots, but very touchy.
500 FSB - 1200 mhz ram = solid works great.
500 FSB - 1250 mhz ram = solid, works fine, just need alittle voltage.
500 FSB - 1300 mhz ram = boots, but unstable, not usable for long term (haha... I cant honestly expect 1300 mhz to be stable)

now heres the monkey wrench...

1200 was stable at 500...

but try 400 FSB - 1200 mhz ram... and it wont boot.

Again, theres some welll just touchy dividers there that just dont seem to like various combinations of FSB and ram.
-------------------------------------------------------------------------------------------

So try many combo of dividers if it will not boot.
A rule is that board like rund numbers better than 1144 1884 and so on

That why pepole can get trouble with memory that have 1111mzh 1140 and so on as mzh.
Some time better to go lower on CAS and mhz.

1066mhz @ 2,175 5-4-4-12-2T-Auto-23-Auto-Auto-Auto
800mhz @ 2,050 4-3-4-10-2T-Auto-19-Auto-Auto-Auto

So when in windows there has to be done stability test.
I use prime blend and 3dmark.
Long test in memtest is a god thing to.

If you get bluscreen-frezze-lock in win
very ofen is memory.
Things to do.
Try go lower-volt-loser timings-lower mzh memory to see if it get better.
Delete swapfile-defrag overall windows knowlegde is important
to.

edit ::::

har uppdaterat bios och nu går det fin fint på default
inga inställningar i bios ....

Hej !

Jag bara undrar .
Efter att ha kikat runt lite här på forumet så verkar det som att
man bara handla av dom stora butikerna

Varför ???????????

Har man inte så brott med leveranserna ( planerat inköp)
och kanske vill ha personlig service
så finns det mindre lokala återförsäljare som har lika bra och bättre priser
på väldigt mycket av produkterna men det vet ni kanske redan ?????

Alltså frågan varför handlar ni där ni handlar ?????

Det finns pengar att tjäna .....tänk på det )

Kolla med din lokala Återförsäljare det kanske lönar sig
(om man har någon i närheten

Ha d gott

KP

Hej!

Ser ok ut ...utom vissa priser (ca 10st) som går att fixa bättre
men eftersom du väljer att köpa allt på Db helt ok
Du har inte skrivit vad du ska använda din dator till
(lättare att bedömma om det blir rätt configuration då )
men med tanke på val av grafik så är det väl mest till spel

Det finns mindre återförsäljare som gör bra jobb tänk på det

mvh

KP